Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8, take 2" from Maxime Ripard:
Another set of changes for the 4.8 merge window, among which:
- Reworking of the DT for the tablets based on Allwinner reference design
and q8 designs to avoid duplication as much as possible
- Renaming a DT merged in the first PR for consistency
- Enable a few devices on some boards
- New boards: Polaroid MID2407PXE03, inet86dz
* tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (21 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: sun7i: bananapi-m1-plus: red LED is power LED
ARM: dts: sun7i: bananapi-m1-plus: Unify suffix for board specific labels
ARM: dts: sun7i: bananapi-m1-plus: Reindent whole file using tabs
ARM: dts: sun7i: lamobo-r1: Enable audio codec
ARM: dts: sun7i: lamobo-r1: Fix GPIO flags in reg_ahci_5v
ARM: dts: sun8i-h3: Rename sinovoip-bpi-m2-plus to bananapi-m2-plus
ARM: dts: sun7i: lamobo-r1: Remove usb1 vbus regulator
...
|
|
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
Merge "DT Changes for 4.8 #3" from Alexandre Belloni:
- Lot of fixes for dtc warnings
- Separate dtb compilation for ARMv4 and ARMv5
* tag 'at91-ab-4.8-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
ARM: dts: at91: sama5d4_ma5d4evk: fix regulator names
ARM: dts: at91: sama5d4_ma5d4: fix regulator names
ARM: dts: at91: sama5d4_xplained: fix regulator names
ARM: dts: at91: sama5d3_xplained: fix regulator name
ARM: dts: at91: sama5d4ek: remove useless lcd_bus
ARM: dts: at91: Fix USB endpoint nodes
Documentation: dt: usb: atmel-usb: add unit-address
ARM: dts: at91: Fix ADC trigger nodes
Documentation: dt: iio: at91_adc: fix trigger node names
|
|
Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.
Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v4.8-rc1" from Thierry Reding:
Some cleanups to existing device tree sources and add Toradex Apalis TK1
support.
* tag 'tegra-for-4.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Initial support for Apalis TK1
ARM: tegra: Remove commas from unit addresses on Tegra124
ARM: tegra: Import latest Jetson TK1 spreadsheet
ARM: tegra: Add spaces around = in properties
ARM: tegra: Fix a couple of DTC warnings
|
|
This patch adds the device tree to support Toradex Apalis TK1 a
computer on module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality which is not yet
supported. Anything that is not self contained on the module is disabled
by default.
The device tree for the Evaluation Board includes the module's device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Banana Pi series is a well known series of single board computers.
The manufacturer, Sinovoip, is less well known. Moreover, the board
markings do not mention Sinovoip, but only the Banana Pi logo, and
the BPI-M* model name.
Rename the dts file to use the more well known name. Also fix up
some of the model names and labels to match other Banana Pi boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
http://github.com/Broadcom/stblinux into next/dt
Merge "additional Broadcom ARM-based SoC Device Tree changes" from Florian Fainelli:
- Lubomir updates all BCM2835 (Raspberry Pi family) Device Tree source files with
their proper information about the on-board USB Ethernet adapter so there is
appropriate binding between this USB device and a device_node (useful for MAC
address fetching and stuff)
- Raveendra adds the ADC controller Device Tree nodes to the Cygnus SoC device
tree include files
- Rafal updates the BCM5301x Device Tree by separating how we specify the NAND
chip-select information in a first change and then fixes the NAND controller
ECC configuration for the D-Link DIR-885L
- Florian adds support for the BCM953012ER reference board, adds the HW random
number generator DT node and adds proper memory node information to the
BCM958625HR reference board
* tag 'arm-soc/for-4.8/devicetree-part2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Specify RAM amount for BCM958625HR board
ARM: BCM5301X: Fix NAND ECC parameters for D-Link DIR-885L
ARM: BCM5301X: Specify NAND chip select and ECC in separated files
ARM: dts: Cygnus: Add Broadcom iproc-static-adc DT node
ARM: dts: BCM5301x: Add BCM953012ER board
ARM: dts: BCM5301x: Add RNG Device Tree node
ARM: bcm2835: dt: Add the ethernet to the device trees
|
|
git://github.com/hisilicon/linux-hisi into next/dt
Merge "ARM: DT: Hisilicon ARMv7 SoC Hi3519 DT updates for 4.8" from Wei Xu:
- Add device tree bindings for hi3519 sysctrl
- Add dts files for hi3519
- Tidy up DTB makefile entries to keep the list sorted
* tag 'hisi-armv7-soc-dt-for-4.8-v2' of git://github.com/hisilicon/linux-hisi:
ARM: dts: add dts files for Hi3519 and tidy up the makefile entries
ARM: dt-bindings: add device tree bindings for Hi3519 sysctrl
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8" from Maxime Ripard:
The usual amount of DT patches, among which:
- I2S support
- Support for the AXP809 in the relevant boards (A80 based)
- New boards: Banapi M1+, Banapi M2+, Allwinner Parrot (R16 EVB),
- The other patches to enable various controllers on our boards, most
notably USB OTG
* tag 'sunxi-dt-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (54 commits)
ARM: dts: sun5i: Enable otg on the auxtex t004
ARM: sun5i: Allow PLL3 2x fixed factor clock to change PLL3 rate
ARM: sun7i: Add DAI nodes
ARM: sun7i: Add mod1 clock nodes
ARM: dts: sun5i: Add mmc1 / sdio-wifi node to mk802
ARM: dts: sun5i: Add axp152 pmic node to mk802
ARM: dts: sun5i: Enable otg on the mk802
ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board
ARM: sun8i: Add Parrot Board DTS
ARM: dts: sun5i: q8-common: Enable USB-based WiFi
ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board
ARM: dts: sun8i-q8-common: Add support for USB wifi controllers
ARM: dts: sun9i: a80-optimus: Order nodes by alphabetical order
ARM: dts: sun9i: cubieboard4: Order nodes by alphabetical order
ARM: dts: sun7i: Add NFC node to Allwinner A20 SoC
ARM: dts: sun4i: Add NFC node to Allwinner A10 SoC
ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts
ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
ARM: dts: sun6i: The blue led on the Mele M9 is a power led
ARM: dts: sun6i: The blue led on the Mele A1000G quad is a power led
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Audio support and spi-flash on rk3288-veyron Chromedevices
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
* tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add support rk3229 evb board
ARM: dts: rockchip: add GMAC nodes for RK322x SoCs
ARM: dts: rockchip: add i2s nodes for RK322x SoCs
ARM: dts: rockchip: rename rk3228.dtsi to rk322x.dtsi
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
ARM: dts: rockchip: rename i2s model for Veyron devices
ARM: dts: rockchip: move rk3288 io-domain nodes to the grf
ARM: dts: rockchip: Enable analog audio on rk3288-veyron chromebooks
ARM: dts: rockchip: Add shared file for audio on rk3288-veyron boards
ARM: dts: rockchip: add SPI flash node for rk3288-veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.8
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
* tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (41 commits)
ARM: dts: r8a7792: add SMP support
ARM: dts: r8a7793: Add APMU node and second CPU core
ARM: dts: r8a7791: Add APMU node
ARM: dts: r8a7790: Add APMU nodes
devicetree: bindings: Renesas APMU and SMP Enable method
ARM: dts: kzm9g: Update console parameters
ARM: dts: kzm9d: Update console parameters
ARM: dts: marzen: Add serial port config to chosen/stdout-path
ARM: dts: genmai: Update console parameters
ARM: dts: armadillo800eva: Update console parameters
ARM: dts: r8a7792: add JPU support
ARM: dts: r8a7792: add JPU clocks
ARM: dts: silk: add DU pins
ARM: dts: blanche: add Ethernet support
ARM: dts: blanche: initial device tree
ARM: dts: blanche: document Blanche board
ARM: dts: r8a7792: add IRQC support
ARM: dts: r8a7792: add [H]SCIF support
ARM: dts: r8a7792: add SYS-DMAC support
ARM: dts: r8a7792: initial SoC device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This adds the Cirrus Logic EP7209,EP7211 DT templates and support for
EDB7211 Development board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
- add dts files for Hi3519
- shuffle ARCH_HIGHBANK, ARCH_HISI, ARCH_HIX5HD2 and ARCH_HIP0X
around to keep the list sorted
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree update for 4.8:
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
* tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D support
ARM: dts: imx7d: move input header into base device tree
ARM: dts: imx7d: recreate imx7d.dtsi with i.MX 7Dual specifics
ARM: dts: imx7d: use imx7s.dtsi as base device tree
ARM: dts: imx7d-sdb: Add support for touchscreen
ARM: dts: imx7d-sdb: Add display support
ARM: dts: imx7d: Add SPI support
ARM: dts: imx6q-bx50v3: Add gpio power off support
ARM: dts: imx6ul-pico-hobbit: Fix Ethernet PHY reset GPIO
ARM: dts: imx6q-tbs2910: fix pcie reset polarity
ARM: dts: imx6sx-sdb: Use WDOG_B pin reset
ARM: dts: imx6ul-evk: Use WDOG_B pin reset
ARM: dts: imx7d-sdb: Use WDOG_B pin reset
ARM: dts: imx6qdl-sabresd: Use WDOG_B pin reset
ARM: dts: utilite-pro: add mmc card slot support
ARM: dts: imx6q-cm-fx6: fix the operation points
ARM: dts: imx6qdl.dtsi: add "arm,shared-override" for pl310
ARM: imx25-pinfunc: remove SION from all modes
ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD
ARM: dts: ls1021a: Add dis_rxdet_inp3_quirk property to USB3 node
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Qualcomm Device Tree Changes for v4.8
* Reverse BAM dma node reverts
* Add BAM remote control options for affected platforms
* Enable peripherals on APQ8074 dragonboard
* Enable PMA8084 pwrky
* Fix PMIC reg entries by removing unnecessary size element
* Add SCM binding and support for all currently supported boards
* Add Qualcomm WCNSS binding documentation
* Rename db600c to SD_600eval and add peripheral nodes
* Remove gpio key entry from Nexus7
* Add APQ8060 based dragonboard and associated peripherals
* Add ARMv7 PMU for IPQ4019
* Update smem state cells to match documentation
* tag 'qcom-dt-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (26 commits)
dts: ipq4019: support ARMv7 PMU
ARM: dts: add Qualcomm APQ8060-based Dragonboard
ARM: dts: move the fixed MMC regulator to SURF board
ARM: dts: fix the MSM8660 RTC base address
ARM: dts: add I2C block in GSBI12
ARM: dts: add L2CC and RPM with regulators for MSM8660
ARM: dts: add SDCC5 to Qualcomm MSM8660
ARM: dts: add GPIO and MPP to MSM8660 PMIC
device-tree: nexus7: Remove power gpio key entry and use pmic8xxx-pwrkey
arm: dts: qcom: Update smem state cells usage
ARM: dts: qcom: msm8974-honami: Set DMA as remotely controlled
ARM: dts: sd_600eval: Fix eMMC lockup issue
ARM: dts: apq8064: rename db600c to SD_600eval
ARM: dts: apq8064: move sdcc3 pinctrls out of baord file
ARM: dts: apq8064: move sdcc1 pinctrl nodes to soc file
dt: binding: Add Qualcomm WCNSS control binding
dts: qcom: apq8064: Add SCM firmware node
dts: qcom: msm8974: Add SCM firmware node
dts: qcom: apq8084: Add SCM firmware node
dt/bindings: firmware: Add Qualcomm SCM binding
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT Changes for 4.8 #2:
- New board: at91sam9260ek
- Fixes for the sam9_l9260
- Sama5d2 Xplained PMIC fix
- Addition of the PMU node for the sama5d2
* tag 'at91-ab-4.8-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2_xplained: Update the pmic node
ARM: dts: at91: sama5d2: add PMU node
ARM: dts: at91: sam9_l9260: Modify information in LED nodes.
ARM: dts: at91: sam9_l9260: Add pinctrl information to ethernet node.
ARM: dts: at91: add at91sam9260ek board DT
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add support for the Bananapi M1 Plus A20 development board from
sinovoip.com.cn . This board is nearly a clone of the Lemaker's
Bananapro, but differ with the wlan chipset connection and i2s pinout.
And I also enable the integrated audio codec on default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.
It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.
The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add Device Tree source file for at91sam9260ek board. This official Atmel
Evaluation Kit is designed around a SoC based on a ARM 926 core the
at91sam9260.
The board is also added to the dts Makefile.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add support for the Broadcom BCM953012 Enterprise Router reference
board, enable the following peripherals:
- UART0 (UART1 is not populated)
- WPS and restart GPIO buttons
- Ethernet switch w/ only two facing ports
- NAND flash
- SPI-NOR flash
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add support for the Computer on Module Colibri iMX7S/iMX7D along
with the development/evaluation carrier board device trees. Follow
the usual hierarchic include model, maintaining shared configuration
in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This is the first Dragonboard based on APQ8060 and PM8058. It
was produced in 2011 in cooperation between Qualcomm and
BSQUARE.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html
So rename this board files so that it reflects actual product in market.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Initial release for rk3229 evb board, and turn the GMAC on.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
http://github.com/Broadcom/stblinux into next/dt
This pull request contains Device Tree changes for Broadcom ARM-based SoCs:
- Chris provides documentation and DTS fixes for the bcm11351 CPU enable-method in preparation
for adding support for the BCM23550 SoC and its corresponding documentation, SoC dtsi
and the Sparrow board DTS file
- Jon adds MSI support to the PCI nodes, updates the secondary cores boot address for the B0
production revision of the Northstar Plus SoC, adds a DTS for the BCM958625HR board, another
one for the BCM958525XMC board, and finally adds the PL330 DMA controller to the NSP DTS
- Rafal enables the SPI NOR flash on dual flash systems (NAND + SPI) on the BCM5301x SoCs
and devices
- Florian adds support for the BCM5301x built-in Ethernet switch by adding nodes for the
Gigabit MAC controllers and the Switch Register Access block, and finally updates the
SmartRG SR-400AC board with its switch port layout
* tag 'arm-soc/for-4.8/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5310x: Enable switch ports on SmartRG SR400AC
ARM: dts: BCM5301X: Add SRAB interrupts
ARM: dts: Enable SRAB switch and GMACs on 5301x DTS
ARM: dts: NSP: Add PL330 support
ARM: dts: NSP: Add XMC board support
ARM: dts: bcm23550: Add device tree files
Documentation: devicetree: Document BCM23550 bindings
ARM: BCM5301X: Enable SPI-NOR on dual flash devices
ARM: dts: NSP: Add new DT file for bcm958625hr
ARM: dts: NSP: modify second CPU address
ARM: dts: NSP: Add MSI support on PCI
ARM: BCM: modify Broadcom CPU enable method
ARM: dts: fix use of bcm11351 enable method
Documentation: Binding docs for bcm11351 enable method
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add the initial device tree for the R8A7792 SoC based Blanche board.
The board has 2 debug serial ports: SCIF0 and SCIF3; include support for
them, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT Changes for 4.8:
- New board: Olimex SAM9-L9260
- Fix crystal definitions for Denx ma5d4
- Remove leftover clock definitions
- Add stdout-path for usb_a9260/a9g20
* tag 'at91-ab-4.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: calao: remove leftovers clock definition
ARM: dts: at91: pm9g45: remove leftovers clock definition
ARM: dts: at91: mpa1600: remove leftovers clock definition
ARM: dts: at91: ge863-pro3: remove leftovers clock definition
ARM: dts: at91: at91-foxg20: remove leftovers clock definition
ARM: dts: at91: at91-cosino: remove leftovers clock definition
ARM: dts: at91: at91-ariag25: remove leftovers clock definition
ARM: dts: at91: animeo_ip: remove leftovers clock definition
ARM: dts: at91: ma5d4: properly define crystals frequencies
ARM: dts: at91: usb_a9g20: use stdout-path
ARM: dts: at91: Add DT support for Olimex SAM9-L9260 board.
ARM: dts: at91: at91sam9260: Remove leading zeros in OHCI node.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Auvidea H100 is a baseboard for the SolidRun MicroSOM.
Its primary feature is a Toshiba TC358743 HDMI to CSI decoder,
allowing the board to work as HDMI passthrough and framegrabber.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The BCM958525XMC board is a smaller form factor typically used as
controller boards for switches. This smaller board has less devices
pinned out, so only a few need be populated in the device tree.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
sam9-l9260 is a low cost board designed by Olimex.
More information is available at:
https://www.olimex.com/Products/ARM/Atmel/SAM9-L9260/
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add device tree files for the Broadcom BCM23550 SoC and the
Broadcom Sparrow board.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
commit 27dd9af6bc000ab21fd ("ARM: dts: sunxi: Add a olinuxino-lime2-emmc")
added the new emmc equipped lime2 but forgot its Makefile.
This patch adds an entry to the Makefile.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Create a new device tree file for the Broadcom Northstar Plus HR SVK.
This SVK is a smaller form factor, and thus only has 2 PCI slots and 1
UART. Also, it has the ability to reboot via GPIO (instead of the
processor reset).
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The Hardkernel's Odroid XU board was first design with big.LITTLE SoC
from Samsung: the Exynos5410. Details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
Comparing this board to Odroid XU3 (more popular), the differences are:
1. Exynos5410 instead of 5422,
2. MIPI DSI LCD connector,
3. Main PMIC: Maxim 77802 instead of S2MPS11,
4. USB3503+LAN9730 instead of integrated LAN9514,
5. eMMC 4.5 instead of eMMC 5.0,
This patch adds initial support for the XU board with working basic
functions, eMMC/SD and USB (including attached ethernet adapter).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Link: http://www.hardkernel.com/main/products/prdt_info.php?g_code=G137510300620
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
|
|
Merge "aspeed devicetree for 4.7" from Joel Stanley:
This device trees for a pair of Aspeed BMC SoCs and the boards that
they sit in.
* tag 'aspeed-for-4.7-dts' of https://github.com/shenki/linux:
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
doc/devicetree: Add Aspeed and Tyan to vendor-prefixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "i.MX device tree updates for 4.7, take 2: from Shawn Guo:
The i.MX device tree updates for 4.7, take 2:
- Update display clock configuration for imx6q-b850v3 board
- Use watchdog external reset for imx6q-ba16 board
- Update operating points settings for i.MX6UL/SX/DL
- New board support: imx6ul-pico-hobbit and imx6q-marsboard
- Add SAI audio support for imx6ul-14x14-evk board
- Enable USB OTG support for M53EVK board
- A couple of fixes on DTC warnings
* tag 'imx-dt-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
ARM: dts: imx6: apalis: parallel lcd display support on ixora
ARM: dts: imx6sx-sdb: Add 198MHz operational point
ARM: dts: imx28-m28: Remove unneeded partition nodes
ARM: dts: imx6ul-pico-hobbit: Add initial support
ARM: dts: imx6: Do not hardcode the CLKO clock
ARM: dts: imx6: Add dts for Embest MarS Board
ARM: dts: imx6: fix dtc warnings for ipu endpoints
ARM: dts: imx6dl: Fix the VDD_ARM_CAP voltage for 396MHz operation
ARM: dts: imx6sx: Add 198MHz operating point
ARM: dts: imx6ul: Fix operating points
ARM: dts: imx6q-ba16: use wdog external reset
ARM: dts: imx: b450/b650v3: Move ldb_di clk assignment
ARM: dts: imx6q-b850v3: Update display clock source
ARM: dts: imx6q-b850v3: Remove ldb panel
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT additions for 4.7" from Maxime Ripard:
The usual bunch of changes, mostly:
* Addition of the SPDIF support
* Addition of the pre-requisites for the display support
* New boards: Difrence DIT4350, colorfly e708 q1, Dserve DSRV9703C,
Polaroid MID2809PXE4, Orange Pi PC, Orange Pi 2
* tag 'sunxi-dt-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (38 commits)
ARM: dts: sun7i: Enable S/PDIF on the Cubietruck
ARM: sun5i: Add DRAM gates
ARM: sun5i: Add TV encoder gate to the DTSI
ARM: sun5i: dt: Add pll3 and pll7 clocks
ARM: dts: sun8i: Add dts file for the Orange Pi One SBC
ARM: sun7i: dt: Enable dram gate 5 (tve0 clock) for simplefb TV output
ARM: sun4i: dt: Enable dram gate 5 (tve0 clock) for simplefb TV output
ARM: dts: sun5i-a13-olinuxino-micro: enable USB DRC
ARM: dts: sun8i: Base Orange Pi Plus dts on the Orange Pi 2 dts
ARM: dts: sun8i: Orangepi plus gpio keys fixes and improvements
ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
ARM: dts: sun8i: Add Orange Pi PC support
ARM: dts: sun8i: Fix pio nodes Orangepi Plus dts
ARM: dts: sun7i: Add SPDIF to the Itead Ibox
ARM: dts: sun4i: Add SPDIF to the Mele A1000
ARM: dts: sun7i: Add the SPDIF block to the A20
ARM: dts: sun4i: Add the SPDIF block to the A10
ARM: dts: sun7i: Add the SPDIF clk to the A20
ARM: dts: sun4i: Add the SPDIF clk to the A10
ARM: dts: sun7i: Add SPDIF TX pin to the A20
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 updates for v4.7 - part2" from Heiko Stübner:
This adds the rk3288-miqi as new board, adapts the edp-phy settings
to the binding-change that made it into 4.6, adds rk3288 i2c controller
nodes and moves the rk3288 thermal data into the soc dtsi, as there
really is no need to have that separate file.
* tag 'v4.7-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the rk3288 thermal data into rk3288.dtsi
ARM: dts: rockchip: add MiQi board from mqmaker
dt-bindings: add vendor-prefix for mqmaker
ARM: dts: rockchip: move rk3288 edp phy under the GRF
ARM: dts: rockchip: make rk3288-grf a simple-mfd
ARM: dts: rockchip: add i2c nodes for RK3228 SoCs
|
|
This adds a common device tree for all fifth generation Aspeed systems,
and a board specific device tree for the ast2500 evaluation board.
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
A common device tree for all forth gen/ast2400 systems and a board
specific dts for the Palmetto OpenPower developemnt machine which was
used for testing.
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add initial support for imx6ul pico hobbit board.
For information about this board, please visit:
http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Part two of device tree changes for omaps for v4.7 merge window" from Tony Lindgren:
- Fix few typos for address-cells and interrupt-names
- Update dra7 voltage rail limits
- Update compatible string for pcf8575 for both nxp and ti prefix
- Add omap5 configuration for gpadc
- Update dra7 for qspi to remove pinmux as it needs to be done by
the bootloader in isolation. Also update the qspi for 64MHz
frequency.
- Add support for Baltos ir2110 and ir3220
- Add industrial and commercial grade thermal thresholds for am57xx
* tag 'omap-for-v4.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-idk: Include Industrial grade thermal thresholds
ARM: dts: am57xx-beagle-x15: Include the commercial grade thresholds
ARM: dts: am57xx: Introduce industrial grade thermal thresholds
ARM: dts: am57xx: Introduce commercial grade thermal thresholds
ARM: dts: add DTS for Baltos IR2110
ARM: dts: add DTS for Baltos IR3220
ARM: dts: split am335x-baltos-ir5221 into dts and dtsi files
ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz
ARM: dts: dra7x: Remove QSPI pinmux
ARM: dts: omap5-board-common: describe gpadc for Palmas
ARM: dts: twl6030: describe gpadc
ARM: dts: dra7xx: Fix compatible string for PCF8575 chip
ARM: dts: AM57xx/DRA7: Update SoC voltage rail limits to match data sheet
ARM: dts: OMAP36xx: : DT spelling s/#address-cell/#address-cells/
ARM: dts: omap5-cm-t54: DT spelling s/interrupt-name/interrupt-names/
ARM: dts: omap5-board-common: DT spelling s/interrupt-name/interrupt-names/
|