Age | Commit message (Collapse) | Author |
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
|
|
|
|
commit 86acc790717fb60fb51ea3095084e331d8711c74 upstream.
Previously, if an non-fatal error was reported by an endpoint, we
called report_error_detected() for the endpoint, every sibling on the
bus, and their descendents. If any of them did not implement the
.error_detected() method, do_recovery() failed, leaving all these
devices unrecovered.
For example, the system described in the bugzilla below has two devices:
0000:74:02.0 [19e5:a230] SAS controller, driver has .error_detected()
0000:74:03.0 [19e5:a235] SATA controller, driver lacks .error_detected()
When a device such as 74:02.0 reported a non-fatal error, do_recovery()
failed because 74:03.0 lacked an .error_detected() method. But per PCIe
r3.1, sec 6.2.2.2.2, such an error does not compromise the Link and
does not affect 74:03.0:
Non-fatal errors are uncorrectable errors which cause a particular
transaction to be unreliable but the Link is otherwise fully functional.
Isolating Non-fatal from Fatal errors provides Requester/Receiver logic
in a device or system management software the opportunity to recover from
the error without resetting the components on the Link and disturbing
other transactions in progress. Devices not associated with the
transaction in error are not impacted by the error.
Report non-fatal errors only to the endpoint that reported them. We really
want to check for AER_NONFATAL here, but the current code structure doesn't
allow that. Looking for pci_channel_io_normal is the best we can do now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197055
Fixes: 6c2b374d7485 ("PCI-Express AER implemetation: AER core and aerdriver")
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 27d6162944b9b34c32cd5841acd21786637ee743 upstream.
When creating virtual functions, create the "virtfn%u" and "physfn" links
in sysfs *before* attaching the driver instead of after. When we attach
the driver to the new virtual network interface first, there is a race when
the driver attaches to the new sends out an "add" udev event, and the
network interface naming software (biosdevname or systemd, for example)
tries to look at these links.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 357027786f3523d26f42391aa4c075b8495e5d28 upstream.
When checking to see if a PCI bus can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set. Children marked with that flag are known not to behave well
after a bus reset.
Some PCIe root port bridges also do not behave well after a bus reset,
sometimes causing the devices behind the bridge to become unusable.
Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to allow these bridges to be flagged, and prevent their secondary buses
from being reset.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 16b6c8bb687cc3bec914de09061fcb8411951fda upstream.
When removing a device, for example a VF being removed due to SR-IOV
teardown, a "soft" hot-unplug via 'echo 1 > remove' in sysfs, or an actual
hot-unplug, we first remove the procfs and sysfs attributes for the device
before attempting to release the device from any driver bound to it.
Unbinding the driver from the device can take time. The device might need
to write out data or it might be actively in use. If it's in use by
userspace through a vfio driver, the unbind might block until the user
releases the device. This leads to a potentially non-trivial amount of
time where the device exists, but we've torn down the interfaces that
userspace uses to examine devices, for instance lspci might generate this
sort of error:
pcilib: Cannot open /sys/bus/pci/devices/0000:01:0a.3/config
lspci: Unable to read the standard configuration space header of device 0000:01:0a.3
We don't seem to have any dependence on this teardown ordering in the
kernel, so let's unbind the driver first, which is also more symmetric with
the instantiation of the device in pci_bus_add_device().
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit fc110ebdd014dd1368c98e7685b47789c31fab42 upstream.
The subordinate value indicates the highest bus number which can be
reached downstream though a certain device.
Commit a20c7f36bd3d ("PCI: Do not allocate more buses than available in
parent") ensures that downstream devices cannot assign busnumbers higher
than the upstream device subordinate number, which was indeed illogical.
By default, dw_pcie_setup_rc() inits the Root Complex subordinate to a
value of 0x01.
Due to this combined with above commit, enumeration stops digging deeper
downstream as soon as bus num 0x01 has been assigned, which is always the
case for a bridge device.
This results in all devices behind a bridge bus remaining undetected, as
these would be connected to bus 0x02 or higher.
Fix this by initializing the RC to a subordinate value of 0xff, which is
not altering hardware behaviour in any way, but informs probing function
pci_scan_bridge() later on which reads this value back from register.
The following nasty errors during boot are also fixed by this:
pci_bus 0000:02: busn_res: can not insert [bus 02-ff] under [bus 01] (conflicts with (null) [bus 01])
...
pci_bus 0000:03: [bus 03] partially hidden behind bridge 0000:01 [bus 01]
...
pci_bus 0000:04: [bus 04] partially hidden behind bridge 0000:01 [bus 01]
...
pci_bus 0000:05: [bus 05] partially hidden behind bridge 0000:01 [bus 01]
pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05
pci_bus 0000:02: busn_res: can not insert [bus 02-05] under [bus 01] (conflicts with (null) [bus 01])
pci_bus 0000:02: [bus 02-05] partially hidden behind bridge 0000:01 [bus 01]
Fixes: a20c7f36bd3d ("PCI: Do not allocate more buses than available in
parent")
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Cc: stable@vger.kernel.org # v4.15+
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Minghuan Lian <minghuan.Lian@freescale.com>
Cc: Mingkai Hu <mingkai.hu@freescale.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit a20c7f36bd3d20d245616ae223bb9d05dfb6f050 upstream.
One can ask more buses to be reserved for hotplug bridges by passing
pci=hpbussize=N in the kernel command line. If the parent bus does not
have enough bus space available we incorrectly create child bus with the
requested number of subordinate buses.
In the example below hpbussize is set to one more than we have available
buses in the root port:
pci 0000:07:00.0: [8086:1578] type 01 class 0x060400
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 0
pci 0000:07:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:08: busn_res: can not insert [bus 08-ff] under [bus 07-3f] (conflicts with (null) [bus 07-3f])
pci_bus 0000:08: scanning bus
...
pci_bus 0000:0a: bus scan returning with max=40
pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 40
pci_bus 0000:0a: [bus 0a-40] partially hidden behind bridge 0000:07 [bus 07-3f]
pci_bus 0000:08: bus scan returning with max=40
pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 40
Instead of allowing this, limit the subordinate number to be less than or
equal the maximum subordinate number allocated for the parent bus (if it
has any).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: remove irrelevant dmesg messages]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 3ad3f8ce50914288731a3018b27ee44ab803e170 upstream.
PCIe PME and native hotplug share the same interrupt number, so hotplug
interrupts are also processed by PME. In some cases, e.g., a Link Down
interrupt, a device may be present but unreachable, so when we try to
read its Root Status register, the read fails and we get all ones data
(0xffffffff).
Previously, we interpreted that data as PCI_EXP_RTSTA_PME being set, i.e.,
"some device has asserted PME," so we scheduled pcie_pme_work_fn(). This
caused an infinite loop because pcie_pme_work_fn() tried to handle PME
requests until PCI_EXP_RTSTA_PME is cleared, but with the link down,
PCI_EXP_RTSTA_PME can't be cleared.
Check for the invalid 0xffffffff data everywhere we read the Root Status
register.
1469d17dd341 ("PCI: pciehp: Handle invalid data when reading from
non-existent devices") added similar checks in the hotplug driver.
Signed-off-by: Qiang Zheng <zhengqiang10@huawei.com>
[bhelgaas: changelog, also check in pcie_pme_work_fn(), use "~0" to follow
other similar checks]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
|
|
commit 7a4db656a6350f8dd46f711bdef3b0e9c6e3f4cb upstream.
PCI core access configuration space registers in resume_noirq callbacks.
In the case of dra7xx, PIPE3 PHY connected to PCIe controller has to be
enabled before accessing configuration space registers. Since
PIPE3 PHY is enabled by only configuring control module registers, no
aborts has been observed so far (though during noirq stage, interface
clock of PIPE3 PHY is not enabled).
With new TRM updates, PIPE3 PHY has to be initialized (PIPE3 PHY
registers has to be accessed) as well which requires the interface
clock of PIPE3 PHY to be enabled. The interface clock of PIPE3 PHY is
derived from OCP2SCP and hence PCIe PHY is modeled as a child of
OCP2SCP. Since pm_runtime is not enabled during noirq stage,
pm_runtime_get_sync done in phy_init doesn't enable
OCP2SCP clocks resulting in abort when PIPE3 PHY registers are
accessed.
Create a function dependency between PCIe and PHY here to make
sure PCIe is suspended before PCIe PHY/OCP2SCP and resumed after
PCIe PHY/OCP2SCP.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
|
|
commit f2ddaf8dfd4a5071ad09074d2f95ab85d35c8a1e upstream.
Extend the Cavium ThunderX ACS quirk to cover more device IDs and restrict
it to only Root Ports.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: changelog, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7f342678634f16795892677204366e835e450dda upstream.
The Cavium ThunderX (CN8XXX) family of PCIe Root Ports does not advertise
an ACS capability. However, the RTL internally implements similar
protection as if ACS had Request Redirection, Completion Redirection,
Source Validation, and Upstream Forwarding features enabled.
Change Cavium ACS capabilities quirk flags accordingly.
Fixes: b404bcfbf035 ("PCI: Add ACS quirk for all Cavium devices")
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: tidy changelog, comment, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.6+: b77d537d00d0: PCI: Apply Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit c00054f540bf81e592e1fee709b0bdbf20f478b5 upstream.
Previously we programmed the LTR_L1.2_THRESHOLD in the parent (upstream)
device using the capability pointer of the *child* (downstream) device,
which corrupted some random word of the parent's config space.
Use the parent's L1 SS capability pointer to program its
LTR_L1.2_THRESHOLD.
Fixes: aeda9adebab8 ("PCI/ASPM: Configure L1 substate settings")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
CC: stable@vger.kernel.org # v4.11+
CC: Rajat Jain <rajatja@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 94ac327e043ee40d7fc57b54541da50507ef4e99 upstream.
Every Port that supports the L1.2 substate advertises its Port
Common_Mode_Restore_Time, i.e., the time the Port requires to re-establish
common mode when exiting L1.2 (see PCIe r3.1, sec 7.33.2).
Per sec 5.5.3.3.1, when exiting L1.2, the Downstream Port (the device at
the upstream end of the link) must send TS1 training sequences for at least
T(COMMONMODE) after it detects electrical idle exit on the Link. We want
this to be long enough for both ends of the Link, so we should set it to
the maximum of the Port Common_Mode_Restore_Time for the upstream and
downstream components on the Link.
Previously we only looked at the Port Common_Mode_Restore_Time of the
upstream device, so if the downstream device required more time, we didn't
program the upstream device's T(COMMONMODE) correctly.
Fixes: f1f0366dd6be ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Rajat Jain <rajatja@google.com>
CC: stable@vger.kernel.org # v4.11+
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
|
|
commit 9561475db680f7144d2223a409dd3d7e322aca03 upstream.
The driver_override implementation is susceptible to a race condition when
different threads are reading vs. storing a different driver override. Add
locking to avoid the race condition.
This is in close analogy to commit 6265539776a0 ("driver core: platform:
fix race condition with driver_override") from Adrian Salido.
Fixes: 782a985d7af2 ("PCI: Introduce new device binding path using pci_dev.driver_override")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 7612b3b28c0b900dcbcdf5e9b9747cc20a1e2455 upstream.
When a power fault occurs, the power controller sets Power Fault Detected
in the Slot Status register, and pciehp_isr() queues an INT_POWER_FAULT
event to handle it.
It also clears Power Fault Detected, but since nothing has yet changed to
correct the power fault, the power controller will likely set it again
immediately, which may cause an infinite loop when pcie_isr() rechecks
Slot Status.
Fix that by masking off Power Fault Detected from new events if the driver
hasn't seen the power fault clear from the previous handling attempt.
Fixes: fad214b0aa72 ("PCI: pciehp: Process all hotplug events before looking for new ones")
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog, pull test out and add comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
commit 48b79a14505349a29b3e20f03619ada9b33c4b17 upstream.
An SHPC may generate MSIs to notify software about slot or controller
events (SHPC spec r1.0, sec 4.7). A PCI device can only generate an MSI if
it has bus mastering enabled.
Enable bus mastering if the bridge contains an SHPC that uses MSI for event
notifications.
Signed-off-by: Aleksandr Bezzubikov <zuban32s@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
pci_call_probe() can called recursively when a physcial function is probed
and the probing creates virtual functions, which are populated via
pci_bus_add_device() which in turn can end up calling pci_call_probe()
again.
The code has an interesting way to prevent recursing into the workqueue
code. That's accomplished by a check whether the current task runs already
on the numa node which is associated with the device.
While that works to prevent the recursion into the workqueue code, it's
racy versus normal execution as there is no guarantee that the node does
not vanish after the check.
There is another issue with this code. It dereferences cpumask_of_node()
unconditionally without checking whether the node is available.
Make the detection reliable by:
- Mark a probed device as 'is_probed' in pci_call_probe()
- Check in pci_call_probe for a virtual function. If it's a virtual
function and the associated physical function device is marked
'is_probed' then this is a recursive call, so the call can be invoked in
the calling context.
- Add a check whether the node is online before dereferencing it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-pci@vger.kernel.org
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081548.771457199@linutronix.de
|
|
Converting the hotplug locking, i.e. get_online_cpus(), to a percpu rwsem
unearthed a circular lock dependency which was hidden from lockdep due to
the lockdep annotation of get_online_cpus() which prevents lockdep from
creating full dependency chains. There are several variants of this. And
example is:
Chain exists of:
cpu_hotplug_lock.rw_sem --> drm_global_mutex --> &item->mutex
CPU0 CPU1
---- ----
lock(&item->mutex);
lock(drm_global_mutex);
lock(&item->mutex);
lock(cpu_hotplug_lock.rw_sem);
because there are dependencies through workqueues. The call chain is:
get_online_cpus
apply_workqueue_attrs
__alloc_workqueue_key
ttm_mem_global_init
ast_ttm_mem_global_init
drm_global_item_ref
ast_mm_init
ast_driver_load
drm_dev_register
drm_get_pci_dev
ast_pci_probe
local_pci_probe
work_for_cpu_fn
process_one_work
worker_thread
This is not a problem of get_online_cpus() recursion, it's a possible
deadlock undetected by lockdep so far.
The cure is to use cpu_hotplug_disable() instead of get_online_cpus() to
protect the PCI probing.
There is a side effect to this: cpu_hotplug_disable() makes a concurrent
cpu hotplug attempt via the sysfs interfaces fail with -EBUSY, but PCI
probing usually happens during the boot process where no interaction is
possible. Any later invocations are infrequent enough and concurrent
hotplug attempts are so unlikely that the danger of user space visible
regressions is very close to zero. Anyway, thats preferrable over a real
deadlock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-pci@vger.kernel.org
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170524081548.691198590@linutronix.de
|
|
commit a477b9cd37aa81a490dfa3265b7ff4f2c5a92463 upstream.
The implementation of PCI workarounds may require that the device is reset
from its probe function. This implies that the PCI device lock is already
held, and makes calling pci_reset_function() impossible (since it will
itself try to take that lock).
Add pci_reset_function_locked(), which is the equivalent of
pci_reset_function(), except that it requires the PCI device lock to be
already held by the caller.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[bhelgaas: folded in fix for conflict with 52354b9d1f46 ("PCI: Remove
__pci_dev_reset() and pci_dev_reset()")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52354b9d1f46aae7386db7bb8ec8484b5488087f upstream.
Implement the reset probing / reset chain directly in
__pci_probe_reset_function() and __pci_reset_function_locked()
respectively.
Link: http://lkml.kernel.org/r/20170601111039.8913-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b014e96d1abbd67404bbe2018937b46466299e9e upstream.
Every method in struct device_driver or structures derived from it like
struct pci_driver MUST provide exclusion vs the driver's ->remove() method,
usually by using device_lock().
Protect use of pci_error_handlers->reset_notify() by holding the device
lock while calling it.
Note:
- pci_dev_lock() calls device_lock() in addition to blocking user-space
config accesses.
- pci_err_handlers->reset_notify() is used inside
pci_dev_save_and_disable() and pci_dev_restore(). We could hold the
device lock directly in pci_reset_notify(), but we expand the region
since we have several calls following each other.
Without this, ->reset_notify() may race with ->remove() calls, which can be
easily triggered in NVMe.
[bhelgaas: changelog, add pci_reset_notify() comment]
[bhelgaas: fold in fix from Dan Carpenter <dan.carpenter@oracle.com>:
http://lkml.kernel.org/r/20170701135323.x5vaj4e2wcs2mcro@mwanda]
Link: http://lkml.kernel.org/r/20170601111039.8913-2-hch@lst.de
Reported-by: Rakesh Pandit <rakesh@tuxera.com>
Tested-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f9a22bc5775d231ab8fbe2c2f3c88e45e3e7c28 upstream.
min_vecs is the minimum amount of vectors needed to operate in MSI-X mode
which may just include the vectors that don't need affinity.
Disabling affinity settings causes the qla2xxx driver scsi_add_host() to fail
when blk_mq is enabled as the blk_mq_pci_map_queues() expects affinity masks
on each vector.
Fixes: dfef358bd1be ("PCI/MSI: Don't apply affinity if there aren't enough vectors left")
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e60514bd4485c0c7c5a7cf779b200ce0b95c70d6 upstream.
Currently we saw a lot of "No irq handler" errors during hibernation, which
caused the system hang finally:
ata4.00: qc timeout (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata4.00: revalidation failed (errno=-5)
ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
do_IRQ: 31.151 No irq handler for vector
According to above logs, there is an interrupt triggered and it is
dispatched to CPU31 with a vector number 151, but there is no handler for
it, thus this IRQ will not get acked and will cause an IRQ flood which
kills the system. To be more specific, the 31.151 is an interrupt from the
AHCI host controller.
After some investigation, the reason why this issue is triggered is because
the thaw_noirq() function does not restore the MSI/MSI-X settings across
hibernation.
The scenario is illustrated below:
1. Before hibernation, IRQ 34 is the handler for the AHCI device, which
is bound to CPU31.
2. Hibernation starts, the AHCI device is put into low power state.
3. All the nonboot CPUs are put offline, so IRQ 34 has to be migrated to
the last alive one - CPU0.
4. After the snapshot has been created, all the nonboot CPUs are brought
up again; IRQ 34 remains bound to CPU0.
5. AHCI devices are put into D0.
6. The snapshot is written to the disk.
The issue is triggered in step 6. The AHCI interrupt should be delivered
to CPU0, however it is delivered to the original CPU31 instead, which
causes the "No irq handler" issue.
Ying Huang has provided a clue that, in step 3 it is possible that writing
to the register might not take effect as the PCI devices have been
suspended.
In step 3, the IRQ 34 affinity should be modified from CPU31 to CPU0, but
in fact it is not. In __pci_write_msi_msg(), if the device is already in
low power state, the low level MSI message entry will not be updated but
cached. During the device restore process after a normal suspend/resume,
pci_restore_msi_state() writes the cached MSI back to the hardware.
But this is not the case for hibernation. pci_restore_msi_state() is not
currently called in pci_pm_thaw_noirq(), although pci_save_state() has
saved the necessary PCI cached information in pci_pm_freeze_noirq().
Restore the PCI status for the device during hibernation. Otherwise the
status might be lost across hibernation (for example, settings for MSI,
MSI-X, ATS, ACS, IOV, etc.), which might cause problems during hibernation.
Suggested-by: Ying Huang <ying.huang@intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: Ying Huang <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc8cca5ef25ac4cb0dfc37467521a759767ff361 upstream.
Rockchip's RC has two banks of registers for the root port: a normal bank
that is strictly compatible with the PCIe spec, and a privileged bank that
can be used to change RO bits of root port registers.
When probing the RC driver, we use the privileged bank to do some basic
setup work as some RO bits are hw-inited to wrong value. But we didn't
change to the normal bank after probing the driver.
This leads to a serious problem when the PME code tries to clear the PME
status by writing PCI_EXP_RTSTA_PME to the register of PCI_EXP_RTSTA. Per
PCIe 3.0 spec, section 7.8.14, the PME status bit is RW1C. So the PME code
is doing the right thing to clear the PME status but we find the RC doesn't
clear it but actually setting it to one. So finally the system trap in
pcie_pme_work_fn() as PCI_EXP_RTSTA_PME is true now forever. This issue
can be reproduced by booting kernel with pci=nomsi.
Use the normal register bank for the PCI config accessors. The privileged
bank is used only internally by this driver.
Fixes: e77f847d ("PCI: rockchip: Add Rockchip PCIe controller support")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0cb259c47a4df466d641c1f07ae3eccaa9ba3ccb upstream.
Recent __call_srcu() changes have exposed that we need to cleanup SRCU
structures after pci_stop_root_bus() calls into vmd_msi_free().
Fixes: 3906b91844d6 ("PCI: vmd: Use SRCU as a local RCU to prevent delaying global RCU")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PCI endpoint test driver uses crc32_le() so it should select
CRC32. Fixes this build error (when CRC32=m):
drivers/built-in.o: In function `pci_epf_test_cmd_handler':
pci-epf-test.c:(.text+0x2d98d): undefined reference to `crc32_le'
Fixes: 349e7a85b25f ("PCI: endpoint: functions: Add an EP function to test PCI")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Callers normally treat the config space accessors as returning PCBIOS_*
error codes, not Linux error codes (or they don't look at them at all). We
have pcibios_err_to_errno() in case the error code needs to be translated.
Fixes: 4b1038834739 ("PCI: Don't attempt config access to disconnected devices")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
Some drivers - like i915 - may not support the system suspend direct
complete optimization due to differences in their runtime and system
suspend sequence. Add a flag that when set resumes the device before
calling the driver's system suspend handlers which effectively disables
the optimization.
Needed by a future patch fixing suspend/resume on i915.
Suggested by Rafael.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
|
|
Commit cc7b0d495589 ("PCI: designware: Update PCI config space remap
function") made PCI configuration requests non-posted, which means we now
get a synchronous abort when the CFG space read to probe for downstream
devices times out.
Synchronous aborts need to be handled differently from the async aborts we
were getting before, in particular the PC needs to be advanced when
resolving the abort. This is mostly a copy of what other PCI drivers do on
ARM to handle those aborts.
[bhelgaas: changelog, "Fixes"]
Fixes: cc7b0d495589 ("PCI: designware: Update PCI config space remap function")
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
|
|
When a switch endpoint is configured without NTB, the mmio_ntb registers
will read all zeros. However, in corner case configurations where the
partition ID is not zero and NTB is not enabled, the code will have the
wrong partition ID and this causes the driver to use the wrong set of
drivers. To fix this we simply take the partition ID from the system info
region.
Reported-by: Dingbao Chen <dingbao.chen@microsemi.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Convert from "cdev_add() + device_add()" to cdev_device_add(), and from
"device_del() + cdev_del()" to cdev_device_del().
[bhelgaas: changelog]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If NO_DMA=y:
drivers/built-in.o: In function `__pci_epc_create':
(.text+0xef4e): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epc_add_epf':
(.text+0xf676): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epf_alloc_space':
(.text+0xfa32): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `pci_epf_free_space':
(.text+0xfac4): undefined reference to `bad_dma_ops'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
|
|
'arm/smmu', 'arm/core', 'x86/vt-d', 'x86/amd' and 'core' into next
|
|
Pull drm u pdates from Dave Airlie:
"This is the main drm pull request for v4.12. Apart from two fixes
pulls, everything should have been in drm-next for at least 2 weeks.
The biggest thing in here is AMD released the public headers for their
upcoming VEGA GPUs. These as always are quite a sizeable chunk of
header files. They've also added initial non-display support for those
GPUs, though they aren't available in production yet.
Otherwise it's pretty much normal.
New bridge drivers:
- megachips-stdpxxxx-ge-b850v3-fw LVDS->DP++
- generic LVDS bridge support.
Core:
- Displayport link train failure reporting to userspace
- debugfs interface cleaned up
- subsystem TODO in kerneldoc now
- Extended fbdev support (flipping and vblank wait)
- drm_platform removed
- EDP CRC support in helper
- HF-VSDB SCDC support in EDID parser
- Lots of code cleanups and header extraction
- Thunderbolt external GPU awareness
- Atomic helper improvements
- Documentation improvements
panel:
- Sitronix and Samsung new panel support
amdgpu:
- Preliminary vega10 support
- Multi-level page table support
- GPU sensor support for userspace
- PRT support for sparse buffers
- SR-IOV improvements
- Non-contig VRAM CPU mapping
i915:
- Atomic modesetting enabled by default on Gen5+
- LSPCON improvements
- Atomic state handling for cdclk
- GPU reset improvements
- In-kernel unit tests
- Geminilake improvements and color manager support
- Designware i2c fixes
- vblank evasion improvements
- Hotplug safe connector iterators
- GVT scheduler QoS support
- GVT Kabylake support
nouveau:
- Acceleration support for Pascal (GP10x).
- Rearchitecture of code handling proprietary signed firmware
- Fix GTX 970 with odd MMU configuration
- GP10B support
- GP107 acceleration support
vmwgfx:
- Atomic modesetting support for vmwgfx
omapdrm:
- Support for render nodes
- Refactor omapdss code
- Fix some probe ordering issues
- Fix too dark RGB565 rendering
sunxi:
- prelim rework for multiple pipes.
mali-dp:
- Color management support
- Plane scaling
- Power management improvements
imx-drm:
- Prefetch Resolve Engine/Gasket on i.MX6QP
- Deferred plane disabling
- Separate alpha support
mediatek:
- Mediatek SoC MT2701 support
rcar-du:
- Gen3 HDMI support
msm:
- 4k support for newer chips
- OPP bindings for gpu
- prep work for per-process pagetables
vc4:
- HDMI audio support
- fixes
qxl:
- minor fixes.
dw-hdmi:
- PHY improvements
- CSC fixes
- Amlogic GX SoC support"
* tag 'drm-for-v4.12' of git://people.freedesktop.org/~airlied/linux: (1778 commits)
drm/nouveau/fb/gf100-: Fix 32 bit wraparound in new ram detection
drm/nouveau/secboot/gm20b: fix the error return code in gm20b_secboot_tegra_read_wpr()
drm/nouveau/kms: Increase max retries in scanout position queries.
drm/nouveau/bios/bitP: check that table is long enough for optional pointers
drm/nouveau/fifo/nv40: no ctxsw for pre-nv44 mpeg engine
drm: mali-dp: use div_u64 for expensive 64-bit divisions
drm/i915: Confirm the request is still active before adding it to the await
drm/i915: Avoid busy-spinning on VLV_GLTC_PW_STATUS mmio
drm/i915/selftests: Allocate inode/file dynamically
drm/i915: Fix system hang with EI UP masked on Haswell
drm/i915: checking for NULL instead of IS_ERR() in mock selftests
drm/i915: Perform link quality check unconditionally during long pulse
drm/i915: Fix use after free in lpe_audio_platdev_destroy()
drm/i915: Use the right mapping_gfp_mask for final shmem allocation
drm/i915: Make legacy cursor updates more unsynced
drm/i915: Apply a cond_resched() to the saturated signaler
drm/i915: Park the signaler before sleeping
drm: mali-dp: Check the mclk rate and allow up/down scaling
drm: mali-dp: Enable image enhancement when scaling
drm: mali-dp: Add plane upscaling support
...
|
|
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
|
|
Pull documentation update from Jonathan Corbet:
"A reasonably busy cycle for documentation this time around. There is a
new guide for user-space API documents, rather sparsely populated at
the moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of
Documentation/ to fix comments elsewhere in the tree; I have acks for
those where I could get them"
* tag 'docs-4.12' of git://git.lwn.net/linux: (74 commits)
docs: Fix a couple typos
docs: Fix a spelling error in vfio-mediated-device.txt
docs: Fix a spelling error in ioctl-number.txt
MAINTAINERS: update file entry for HSI subsystem
Documentation: allow installing man pages to a user defined directory
Doc/PM: Sync with intel_powerclamp code behavior
zr364xx.rst: usb/devices is now at /sys/kernel/debug/
usb.rst: move documentation from proc_usb_info.txt to USB ReST book
convert philips.txt to ReST and add to media docs
docs-rst: usb: update old usbfs-related documentation
arm: Documentation: update a path name
docs: process/4.Coding.rst: Fix a couple of document refs
docs-rst: fix usb cross-references
usb: gadget.h: be consistent at kernel doc macros
usb: composite.h: fix two warnings when building docs
usb: get rid of some ReST doc build errors
usb.rst: get rid of some Sphinx errors
usb/URB.txt: convert to ReST and update it
usb/persist.txt: convert to ReST and add to driver-api book
usb/hotplug.txt: convert to ReST and add to driver-api book
...
|
|
Many PCI host controller drivers aren't prepared to have their devices
unbound from them forcefully (e.g., through /sys/.../<driver>/unbind), as
they don't provide any driver .remove callback, where they'd detach the
root bus, release resources, etc. Keeping the driver built in (i.e., not a
loadable module) is not enough; and providing no .remove callback just
means we don't do any teardown.
To rule out the possibility of unbinding a device via sysfs, we need to set
the ".suppress_bind_attrs" field.
I found the suspect drivers via the following search:
git grep -l platform_driver $(git grep -L -e '\.remove' -e suppress_bind_attrs drivers/pci/)
Then I inspected them to ensure that
(a) they set up a PCI bus in their probe() and
(b) they don't have a remove() callback for undoing the setup
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
* pci/virtualization:
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: Call pcie_flr() from reset_chelsio_generic_dev()
PCI: Call pcie_flr() from reset_intel_82599_sfp_virtfn()
PCI: Export pcie_flr()
PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding
PCI: Avoid FLR for Intel 82579 NICs
Conflicts:
include/linux/pci.h
|
|
* pci/resource-mmap:
ia64: Use generic pci_mmap_resource_range()
ia64: Remove redundant checks for WC in pci_mmap_page_range()
ia64: Remove redundant valid_mmap_phys_addr_range() from pci_mmap_page_range()
PCI: Add I/O BAR support to generic pci_mmap_resource_range()
x86/PCI: Use generic pci_mmap_resource_range()
unicore32/PCI: Use generic pci_mmap_resource_range()
sh/PCI: Use generic pci_mmap_resource_range()
parisc: Use generic pci_mmap_resource_range()
mn10300/PCI: Use generic pci_mmap_resource_range()
MIPS: PCI: Use generic pci_mmap_resource_range()
cris/PCI: Use generic pci_mmap_resource_range()
ARM/PCI: Use generic pci_mmap_resource_range()
PCI: Add pci_mmap_resource_range() and use it for ARM64
PCI: Add BAR index argument to pci_mmap_page_range()
PCI: Use BAR index in sysfs attr->private instead of resource pointer
PCI: Add arch_can_pci_mmap_io() on architectures which can mmap() I/O space
PCI: Move multiple declarations of pci_mmap_page_range() to <linux/pci.h>
PCI: Add arch_can_pci_mmap_wc() macro
xtensa/PCI: Do not mmap PCI BARs to userspace as write-through
PCI: Only allow WC mmap on prefetchable resources
PCI: Fix another sanity check bug in /proc/pci mmap
PCI: Fix pci_mmap_fits() for HAVE_PCI_RESOURCE_TO_USER platforms
|
|
* pci/resource:
PCI: Don't resize resources when realigning all devices in system
PCI: Don't reassign resources that are already aligned
PCI: Factor pci_reassigndev_resource_alignment()
powerpc/powernv: Override pcibios_default_alignment() to force PCI devices to be page aligned
PCI: Add pcibios_default_alignment() for arch-specific alignment control
PCI: Fix calculation of bridge window's size and alignment
PCI: Ignore requested alignment for IOV BARs
PCI: Make PCI_ROM_ADDRESS_MASK a 32-bit constant
|
|
* pci/pm:
PCI: Freeze PME scan before suspending devices
PCI/PM: Don't sleep at all when d3_delay or d3cold_delay is zero
|
|
* pci/msi:
PCI/MSI: Use dev_printk() when possible
of/pci: Remove unused MSI controller helpers
PCI: mvebu: Remove useless MSI enabling code
PCI: aardvark: Move to MSI handling using generic MSI support
PCI/MSI: Make pci_msi_shutdown() and pci_msix_shutdown() static
PCI/MSI: Stop disabling MSI/MSI-X in pci_device_shutdown()
|
|
* pci/misc:
PCI: Change pci_host_common_probe() visibility
PCI: Fix typo pci_cfg_access_lock() comment
PCI: Include pci.h for struct pci_ops definition
|