| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 061870800efb4e3d1ad4082a2569363629bdfcfc ]
Completion on timeout should not free the driver command entry structure
as it will need to access it again once real completion event from FW
will occur.
Fixes: 73dd3a4839c1 ('net/mlx5: Avoid using pending command interface slots')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dc798b4cc0f2a06e7ad7d522403de274b86a0a6f ]
The tx_enabled lag event field is used to determine whether a slave is
active.
Current logic uses this value only if the mode is active-backup.
However, LACP mode, although considered a load balancing mode, can mark
a slave as inactive in certain situations (e.g., LACP timeout).
This fix takes the tx_enabled value into account when remapping, with
no respect to the LAG mode (this should not affect the behavior in XOR
mode, since in this mode both slaves are marked as active).
Fixes: 7907f23adc18 (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4813497b537c6208c90d6cbecac5072d347de900 ]
Before commit bf8f6952a233 ("Add blurb about RGMII") it was unclear
whose responsibility it was to insert the required clock skew, and
in hindsight, some PHY drivers got it wrong. The solution forward
is to introduce a new property, explicitly requiring skew from the
node to which it is attached. In the interim, this driver will handle
all 4 RGMII modes identically (no skew).
Fixes: 52dfc8301248 ("net: ethernet: add driver for Aurora VLSI NB8800 Ethernet controller")
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 440aeca4b9858248d8f16d724d9fa87a4f65fa33 upstream.
The functions igb_read_phy_reg_gs40g/igb_write_phy_reg_gs40g (which were
removed in 2a3cdea) explicitly selected the required page at every phy_reg
access. Currently, igb_get_phy_id_82575 relays on the fact that page 0 is
already selected. The assumption is not fulfilled for my Lex 3I380CW
motherboard with integrated dual i211 based gigabit ethernet. This leads to igb
initialization failure and network interfaces are not working:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
igb: probe of 0000:02:00.0 failed with error -2
In order to fix it, we explicitly select page 0 before first access to phy
registers.
See also: https://bugzilla.suse.com/show_bug.cgi?id=1009911
See also: http://www.lex.com.tw/products/pdf/3I380A&3I380CW.pdf
Fixes: 2a3cdea ("igb: Remove GS40G specific defines/functions")
Signed-off-by: Matwey V Kornilov <matwey@sai.msu.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c70d68150f71b84cea6997a53493e17bf18a54db ]
If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.
Fixes: 12fb0da45c9a ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6a146f3a5894b751cef16feb3d7903e45e3c445c ]
Since the introduction of ULD (Upper-Layer Drivers), the MSI-X
deallocating path changed in cxgb4: the driver frees the interrupts
of ULD when unregistering it or on shutdown PCI handler.
Problem is that if a MSI-X is not freed before deallocated in the PCI
layer, it will trigger a BUG() due to still "alive" interrupt being
tentatively quiesced.
The below trace was observed when doing a simple unbind of Chelsio's
adapter PCI function, like:
"echo 001e:80:00.4 > /sys/bus/pci/drivers/cxgb4/unbind"
Trace:
kernel BUG at drivers/pci/msi.c:352!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c0000000005a5e60] free_msi_irqs+0xa0/0x250
LR [c0000000005a5e50] free_msi_irqs+0x90/0x250
Call Trace:
[c0000000005a5e50] free_msi_irqs+0x90/0x250 (unreliable)
[c0000000005a72c4] pci_disable_msix+0x124/0x180
[d000000011e06708] disable_msi+0x88/0xb0 [cxgb4]
[d000000011e06948] free_some_resources+0xa8/0x160 [cxgb4]
[d000000011e06d60] remove_one+0x170/0x3c0 [cxgb4]
[c00000000058a910] pci_device_remove+0x70/0x110
[c00000000064ef04] device_release_driver_internal+0x1f4/0x2c0
...
This patch fixes the issue by refactoring the shutdown path of ULD on
cxgb4 driver, by properly freeing and disabling interrupts on PCI
remove handler too.
Fixes: 0fbc81b3ad51 ("Allocate resources dynamically for all cxgb4 ULD's")
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d968f0f2e4404152f37ed2384b4a2269dd2dae5a ]
Latest change in open-lldp code uses bytes 6-11 of perm_addr buffer
as the Ethernet source address for the host TLV packet.
Since our driver does not fill these bytes, they stay at zero and
the open-lldp code ends up sending the TLV packet with zero source
address and the switch drops this packet.
The fix is to initialize these bytes to 0xff. The open-lldp code
considers 0xff:ff:ff:ff:ff:ff as the invalid address and falls back to
use the host's mac address as the Ethernet source address.
Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 05a6b4cae8c0cc1680c9dd33a97a49a13c0f01bc ]
The code that detects a failed soft reset of Octeon is comparing the wrong
value against the reset value of the Octeon SLI_SCRATCH_1 register,
resulting in an inability to detect a soft reset failure. Fix it by using
the correct value in the comparison, which is any non-zero value.
Fixes: f21fb3ed364b ("Add support of Cavium Liquidio ethernet adapters")
Fixes: c0eab5b3580a ("liquidio: CN23XX firmware download")
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8ff93de7668bd81bc8efa819d1184ebd48fae72d ]
Symbol error during carrier counter from PPCNT was mistakenly reported as
TX carrier errors in get_stats ndo, although it's an RX counter.
Fixes: 269e6b3af3bf ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2a0165a034ac024b60cca49c61e46f4afa2e4d98 ]
Draining the health workqueue will ignore future health works including
the one that report hardware failure and thus we can't enter error state
Instead cancel the recovery flow and make sure only recovery flow won't
be scheduled.
Fixes: 5e44fca50470 ('net/mlx5: Only cancel recovery work when cleaning up device')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8ce59b16b4b6eacedaec1f7b652b4781cdbfe15f ]
When wait for firmware init fails, previous code would mistakenly
return success and cause inconsistency in the driver state.
Fixes: 6c780a0267b8 ("net/mlx5: Wait for FW readiness before initializing command interface")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When filter insertion fails with no rollback, we were trying to convert
EFX_EF10_FILTER_ID_INVALID to an id to store in 'ids' (which is either
vlan->uc or vlan->mc). This would WARN_ON_ONCE and then record a bogus
filter ID of 0x1fff, neither of which is a good thing.
Fixes: 0ccb998bf46d ("sfc: fix filter_id misinterpretation in edge case")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My static checker complains that ofdpa_neigh_del() can sometimes free
"found". It just makes sense to use it first before deleting it.
Fixes: ecf244f753e0 ("rocker: fix maybe-uninitialized warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a VLAN device is enslaved to a bridge we shouldn't create a
router interface (RIF) for it when it's configured with an IP address.
This is already handled by the driver for other types of netdevs, such
as physical ports and LAG devices.
If this IP address is then removed and the interface is subsequently
unlinked from the bridge, a NULL pointer dereference can happen, as the
original 802.1d FID was replaced with an rFID which was then deleted.
To reproduce:
$ ip link set dev enp3s0np9 up
$ ip link add name enp3s0np9.111 link enp3s0np9 type vlan id 111
$ ip link set dev enp3s0np9.111 up
$ ip link add name br0 type bridge
$ ip link set dev br0 up
$ ip link set enp3s0np9.111 master br0
$ ip address add dev enp3s0np9.111 192.168.0.1/24
$ ip address del dev enp3s0np9.111 192.168.0.1/24
$ ip link set dev enp3s0np9.111 nomaster
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Tested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A previous commit (5567e989198b5a8d) inserted a dependency on DMA
API that requires HAS_DMA to be added in Kconfig.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mc configuration changes bnx2x_config_mcast() can return 0 for
success, negative for failure and positive for benign reason preventing
its immediate work, e.g., when the command awaits the completion of
a previously sent command.
When removing all configured macs on a 578xx adapter, if a positive
value would be returned driver would errneously log it as an error.
Fixes: c7b7b483ccc9 ("bnx2x: Don't flush multicast MACs")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To handle netpoll properly, the driver must only handle TX packets
during NAPI. Handling RX events cause warnings and errors in
netpoll mode. The ndo_poll_controller() method should call
napi_schedule() directly so that a NAPI weight of zero will be used
during netpoll mode.
The bnxt_en driver supports 2 ring modes: combined, and separate rx/tx.
In separate rx/tx mode, the ndo_poll_controller() method will only
process the tx rings. In combined mode, the rx and tx completion
entries are mixed in the completion ring and we need to drop the rx
entries and recycle the rx buffers.
Add a function bnxt_force_rx_discard() to handle this in netpoll mode
when we see rx entries in combined ring mode.
Reported-by: Calvin Owens <calvinowens@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we get a TPA_END completion to handle a completed LRO packet, it
is possible that hardware would indicate errors. The current code is
not checking for the error condition. Define the proper error bits and
the macro to check for this error and abort properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 8000 series adapters uses catch-all filters for encapsulated traffic
to support filtering VXLAN, NVGRE and GENEVE traffic.
This new filter functionality requires a longer MCDI command.
This patch increases the size of buffers on stack that were missed, which
fixes a kernel panic from the stack protector.
Fixes: 9b41080125176 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Bert Kenward bkenward@solarflare.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When having the skb pointer in the first descriptor, stmmac_tx_clean
can get called at a moment where the IP has only cleared the own bit
of the first descriptor, thus freeing the skb, even though there can
be several descriptors whose buffers point into the same skb.
By simply moving the skb pointer from the first descriptor to the last
descriptor, a skb will get freed only when the IP has cleared the
own bit of all the descriptors that are using that skb.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Somehow two copies of the line 'up_write(&vf->efx->filter_sem);' got into
efx_ef10_sriov_set_vf_vlan(). This would put the mutex in a bad state and
cause all subsequent down attempts to hang.
Fixes: 671b53eec2ed ("sfc: Ensure down_write(&filter_sem) and up_write() are matched before calling efx_net_open()")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the use of arch_setup_dma_ops() that was not exported
and was breaking loadable module compilation.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure dma_ops are set, to be later used by the Ethernet driver.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the phy loopback self_test failed issue. when
Marvell Phy Module is loaded, it will powerdown fiber when doing
phy loopback self test, which cause phy loopback self_test fail.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the module initialisation there is a possible race
(basically race between uld and lld) where neither the uld
nor lld notifies the uP about where to route the ctrl queue
completions. LLD skips notifying uP as the rdma queues were
not created by then (will leave it to ULD to notify the uP).
As the ULD comes up, it also skips notifying the uP as the
flag FULL_INIT_DONE is not set yet (ULD assumes that the
interface is not up yet).
Consequently, this race between uld and lld leaves uP
unnotified about where to send the ctrl queue completions
to, leading to iwarp RI_RES WR failure.
Here is the race:
CPU 0 CPU1
- allocates nic rx queus
- t4_sge_alloc_ctrl_txq()
(if rdma rsp queues exists,
tell uP to route ctrl queue
compl to rdma rspq)
- acquires the mutex_lock
- allocates rdma response queues
- if FULL_INIT_DONE set,
tell uP to route ctrl queue compl
to rdma rspq
- relinquishes mutex_lock
- acquires the mutex_lock
- enable_rx()
- set FULL_INIT_DONE
- relinquishes mutex_lock
This patch fixes the above issue.
Fixes: e7519f9926f1('cxgb4: avoid enabling napi twice to the same queue')
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
CC: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.
Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.
Fixes: 26e59d8077a3 '(net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the firmware API is partial and allows to offload only
the dscp part of the tos, also, ipv6 support isn't there yet.
As such, remove the offloading option of ipv4 dscp till the FW
APIs are more comprehensive.
Fixes: d79b6df6b10a ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently we don't check that the link type is Eth and hence crash
on IB ports when attempting to deref esw->xxx, fix that.
To avoid repeating this check over and over, put the existing
checks and the one on link type in a single helper.
Fixes: 7768d1971de6 ('net/mlx5: E-Switch, Add control for encapsulation')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Mohamad Badarnah <mohamadb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.
This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.
Fixes: a6f402e49901 ("net/mlx5e: Tx, no inline copy on ConnectX-5")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Misuse of (BIT) macro caused to report wrong flags for
"Hardware Transmit Timestamp Modes" and "Hardware Receive
Filter Modes"
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Fixes: e3297246c2c8 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
i40e_vsi_remove_pvid
i40e_vlan_stripping_disable
i40e_aq_update_vsi_params
i40e_asq_send_command
mutex_lock --> may sleep
To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when dumping a context data only word number '1' is read for the
entire context.
Fixes: c965db444629 ("qed: Add support for debug data collection")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a36 ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox mlx5 fixes 2017-06-11
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Added BW check for DIM decision mechanism") kernels >= 4.9
("net/mlx5e: Fix wrong indications in DIM due to counter wraparound") kernels >= 4.9
("net/mlx5: Remove several module events out of ethtool stats") kernels >= 4.10
("net/mlx5: Enable 4K UAR only when page size is bigger than 4K") kernels >= 4.11
*all patches apply with no issue on their -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
check_for_missing_tx_completions() is called from a timer
task and looking for lost tx packets.
The old implementation accumulate all the lost tx packets
and did not check if those packets were retrieved on a later stage.
This cause to a situation where the driver reset
the device for no reason.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the rare case where the device runs out of free rx buffer
descriptors (in case of pressure on kernel memory),
and the napi handler continuously fail to refill new Rx descriptors
until device rx queue totally runs out of all free rx buffers
to post incoming packet, leading to a deadlock:
* The device won't send interrupts since all the new
Rx packets will be dropped.
* The napi handler won't try to allocate new Rx descriptors
since allocation is part of NAPI that's not being invoked any more
The fix involves detecting this scenario and rescheduling NAPI
(to refill buffers) by the keepalive/watchdog task.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch also change the mapping functions to devm_ functions
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug:
"Completion context is occupied" error printout will be noticed in
dmesg.
This error will cause the admin command to fail, which will lead to
an ena_probe() failure or a watchdog reset (depends on which admin
command failed).
Root cause:
__ena_com_submit_admin_cmd() is the function that submits new entries to
the admin queue.
The function have a check that makes sure the queue is not full and the
function does not override any outstanding command.
It uses head and tail indexes for this check.
The head is increased by ena_com_handle_admin_completion() which runs
from interrupt context, and the tail index is increased by the submit
function (the function is running under ->q_lock, so there is no risk
of multithread increment).
Each command is associated with a completion context. This context
allocated before call to __ena_com_submit_admin_cmd() and freed by
ena_com_wait_and_process_admin_cq_interrupts(), right after the command
was completed.
This can lead to a state where the head was increased, the check passed,
but the completion context is still in use.
Solution:
Use the atomic variable ->outstanding_cmds instead of using the head and
the tail indexes.
This variable is safe for use since it is bumped in get_comp_ctx() in
__ena_com_submit_admin_cmd() and is freed by comp_ctxt_release()
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixing a bug that the driver does not unmask the IO interrupts
in ndo_open():
occasionally, the MSI-X interrupt (for one or more IO queues)
can be masked when ndo_close() was called.
If that is followed by ndo open(),
then the MSI-X will be still masked so no interrupt
will be received by the driver.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current flow to detect admin completion is:
while (command_not_completed) {
if (timeout)
error
check_for_completion()
sleep()
}
So in case the sleep took more than the timeout
(in case the thread/workqueue was not scheduled due to higher priority
task or prolonged VMexit), the driver can detect a stall even if
the completion is present.
The fix changes the order of this function to first check for
completion and only after that check if the timeout expired.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the page size isn't bigger than 4K, there is no added value of enabling 4K
UAR feature in the Firmware.
Modified the condition of enabling the 4K UAR accordingly.
Fixes: f502d834950a ("net/mlx5: Activate support for 4K UARs")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Each iteration of the algorithm, DIM calculates the difference in
throughput, packet rate and interrupt rate from last iteration in order
to make a decision. DIM relies on counters for each metric. When these
counters get to their type's max value they wraparound. In this case
the delta between 'end' and 'start' samples is negative and when
translated to unsigned integers - very high. This results in a false
indication to the algorithm and might result in a wrong decision.
The fix calculates the 'distance' between 'end' and 'start' samples in a
cyclic way around the relevant type's max value. It can also be viewed as
an absolute value around the type's max value instead of around 0.
Testing show higher stability in DIM profile selection and no wraparound
issues.
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Until now only interrupt and packet rate were sampled.
We found a scenario on which we get a false indication since a change in
DIM caused more aggregation and reduced packet rate while increasing BW.
We now regard a change as succesfull iff:
current_BW > (prev_BW + threshold) or
current_BW ~= prev_BW and current_PR > (prev_PR + threshold) or
current_BW ~= prev_BW and current_PR ~= prev_PR and
current_IR < (prev_IR - threshold)
Where BW = Bandwidth, PR = Packet rate and IR = Interrupt rate
Improvements (ConnectX-4Lx 25GbE, single RX queue, LRO off)
--------------------------------------------------
packet size | before[Mb/s] | after[Mb/s] | gain |
2B | 343.4 | 359.4 | 4.5% |
16B | 2739.7 | 2814.8 | 2.7% |
64B | 9739 | 10185.3 | 4.5% |
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Remove the following module event counters out of ethtool stats. The
reason for removing these event counters is that these events do not
occur without techinician's intervention.
module_pwr_budget_exd
module_long_range
module_no_eeprom
module_enforce_part
module_unknown_id
module_unknown_status
module_plug
Fixes: bedb7c909c19 ("net/mlx5e: Add port module event counters to ethtool stats")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The issue is that when we get an assert we will stop polling the health
and thus we cant enter error state when we have a real health issue.
Fixes: fd76ee4da55a ('net/mlx5_core: Fix internal error detection conditions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
Moshe Shemesh
Aviv Heller
Marc Gonzalez
Matwey V Kornilov
Bert Kenward
Guilherme G. Piccoli
Huy Nguyen
Derek Chickles
Gal Pressman
Mohamad Haj Yahia
Edward Cree
Dan Carpenter
Ido Schimmel
Madalin Bucur
Mintz, Yuval
Michael Chan
Martin Habets
Lokesh Vutla
Niklas Cassel
Lin Yun Sheng
Raju Rangoju
Or Gerlitz
Chris Mi
Maor Dickman
Eli Cohen
Jia-Ju Bai
Tayar, Tomer
Jacob Keller
David S. Miller
Netanel Belgazal
Majd Dibbiny
Tal Gilboa