| Age | Commit message (Collapse) | Author |
|---|
|
|
|
commit 72fd50e14e46dc0edf360631bdece87c2f066a97 upstream.
The req_canceled() callback is used by tpm_transmit() periodically to
check whether the request has been canceled while it is receiving a
response from the TPM.
The TPM_CRB_CTRL_CANCEL register was cleared already in the crb_cancel
callback, which has two consequences:
* Cancel might not happen.
* req_canceled() always returns zero.
A better place to clear the register is when starting to send a new
command. The behavior of TPM_CRB_CTRL_CANCEL is described in the
section 5.5.3.6 of the PTP specification.
Fixes: 30fc8d138e91 ("tpm: TPM 2.0 CRB Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4816edfe706497a8525480c1685ceb9871bc118 upstream.
Unseal and load operations should be done as an atomic operation. This
commit introduces unlocked tpm_transmit() so that tpm2_unseal_trusted()
can do the locking by itself.
Fixes: 0fe5480303a1 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e71b9dff0634edb127f449e076e883ef24a8c76c upstream.
Ima tries to call ->setxattr() on overlayfs dentry after having locked
underlying inode, which results in a deadlock.
Reported-by: Krisztian Litkey <kli@iki.fi>
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af48d7bc3756a0cd882d65bff14ab39746ba57fe upstream.
We know that 'ret = 0' because it has been tested a few lines above.
So, if 'kzalloc' fails, 0 will be returned instead of an error code.
Return -ENOMEM instead.
Fixes: a0d46a3dfdc3 ("ARM: cpuidle: Register per cpuidle device")
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca88696e8b73a9fa2b1de445747e9235c3a7bd50 upstream.
The Qualcomm PMIC GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
Fixes: bce360469676 ("ARM: dts: apq8064: add pm8921 mpp support")
Fixes: 874443fe9e33 ("ARM: dts: apq8064: Add pm8921 mfd and its gpio node")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 061492cfad9f11dbc32df741a7164f307b69b6e6 upstream.
The armada-390.dtsi was broken since the first patch which adds Device Tree
files for Armada 39x SoC was introduced.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes 538da83 ("ARM: mvebu: add Device Tree files for Armada 39x SoC and board")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
commit 72b4f6a5e903b071f2a7c4eb1418cbe4eefdc344 upstream.
On x86_32, when an interrupt happens from kernel space, SS and SP aren't
pushed and the existing stack is used. So pt_regs is effectively two
words shorter, and the previous stack pointer is normally the memory
after the shortened pt_regs, aka '®s->sp'.
But in the rare case where the interrupt hits right after the stack
pointer has been changed to point to an empty stack, like for example
when call_on_stack() is used, the address immediately after the
shortened pt_regs is no longer on the stack. In that case, instead of
'®s->sp', the previous stack pointer should be retrieved from the
beginning of the current stack page.
kernel_stack_pointer() wants to do that, but it forgets to dereference
the pointer. So instead of returning a pointer to the previous stack,
it returns a pointer to the beginning of the current stack.
Note that it's probably outside of kernel_stack_pointer()'s scope to be
switching stacks at all. The x86_64 version of this function doesn't do
it, and it would be better for the caller to do it if necessary. But
that's a patch for another day. This just fixes the original intent.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0788aa6a23cb ("x86: Prepare removal of previous_esp from i386 thread_info structure")
Link: http://lkml.kernel.org/r/472453d6e9f6a2d4ab16aaed4935f43117111566.1471535549.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba6d018e3d2f6a0fad58a668cadf66b2d1f80f59 upstream.
__show_regs() fails to dump the PKRU state when the debug registers are in
their default state because there is a return statement on the debug
register state.
Change the logic to report PKRU value even when debug registers are in
their default state.
Fixes:c0b17b5bd4b7 ("x86/mm/pkeys: Dump PKRU with other kernel registers")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://lkml.kernel.org/r/20160910183045.4618-1-nicolas.iooss_linux@m4x.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2a51fe083eba7f99cbda72f5ef90cdf2f4df882c upstream.
When a CPU is physically added to a system then the MADT table is not
updated.
If subsequently a kdump kernel is started on that physically added CPU then
the ACPI enumeration fails to provide the information for this CPU which is
now the boot CPU of the kdump kernel.
As a consequence, generic_processor_info() is not invoked for that CPU so
the number of enumerated processors is 0 and none of the initializations,
including the logical package id management, are performed.
We have code which relies on the correctness of the logical package map and
other information which is initialized via generic_processor_info().
Executing such code will result in undefined behaviour or kernel crashes.
This problem applies only to the kdump kernel because a normal kexec will
switch to the original boot CPU, which is enumerated in MADT, before
jumping into the kexec kernel.
The boot code already has a check for num_processors equal 0 in
prefill_possible_map(). We can use that check as an indicator that the
enumeration of the boot CPU did not happen and invoke generic_processor_info()
for it. That initializes the relevant data for the boot CPU and therefore
prevents subsequent failure.
[ tglx: Refined the code and rewrote the changelog ]
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Fixes: 1f12e32f4cd5 ("x86/topology: Create logical package id")
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: dyoung@redhat.com
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: kexec@lists.infradead.org
Link: http://lkml.kernel.org/r/1475514432-27682-1-git-send-email-prarit@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cff9ab2b291e64259d97add48fe073c081afe4e2 upstream.
The array has a size of MAX_LOCAL_APIC, which can be as large as 32k, so it
can consume up to 128k.
The array has been there forever and was never used for anything useful
other than a version mismatch check which was introduced in 2009.
There is no reason to store the version in an array. The kernel is not
prepared to handle different APIC versions anyway, so the real important
part is to detect a version mismatch and warn about it, which can be done
with a single variable as well.
[ tglx: Massaged changelog ]
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Borislav Petkov <bp@alien8.de>
CC: Brian Gerst <brgerst@gmail.com>
CC: Mike Travis <travis@sgi.com>
Link: http://lkml.kernel.org/r/20160913181232.30815-1-dvlasenk@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4b05923f579c234137317cdf9a5eb69ddab76d1 upstream.
Our XSAVE features are divided into two categories: those that
generate FPU exceptions, and those that do not. MPX and pkeys do
not generate FPU exceptions and thus can not be used lazily. We
disable them when lazy mode is forced on.
We have a pair of masks to collect these two sets of features, but
XFEATURE_MASK_PKRU was added to the wrong mask: XFEATURE_MASK_LAZY.
Fix it by moving the feature to XFEATURE_MASK_EAGER.
Note: this only causes problem if you boot with lazy FPU mode
(eagerfpu=off) which is *not* the default. It also only affects
hardware which is not currently publicly available. It looks like
eager mode is going away, but we still need this patch applied
to any kernel that has protection keys and lazy mode, which is 4.6
through 4.8 at this point, and 4.9 if the lazy removal isn't sent
to Linus for 4.9.
Fixes: c8df40098451 ("x86/fpu, x86/mm/pkeys: Add PKRU xsave fields and data structures")
Signed-off-by: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20161007162342.28A49813@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db91aa793ff984ac048e199ea1c54202543952fe upstream.
When a CPU is about to be offlined we call fixup_irqs() that resets IRQ
affinities related to the CPU in question. The same thing is also done when
the system is suspended to S-states like S3 (mem).
For each IRQ we try to complete any on-going move regardless whether the
IRQ is actually part of x86_vector_domain. For each IRQ descriptor we fetch
its chip_data, assume it is of type struct apic_chip_data and manipulate it
by clearing old_domain mask etc. For irq_chips that are not part of the
x86_vector_domain, like those created by various GPIO drivers, will find
their chip_data being changed unexpectly.
Below is an example where GPIO chip owned by pinctrl-sunrisepoint.c gets
corrupted after resume:
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in hi
# rtcwake -s10 -mmem
<10 seconds passes>
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in ?
Note '?' in the output. It means the struct gpio_chip ->get function is
NULL whereas before suspend it was there.
Fix this by first checking that the IRQ belongs to x86_vector_domain before
we try to use the chip_data as struct apic_chip_data.
Reported-and-tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: http://lkml.kernel.org/r/20161003101708.34795-1-mika.westerberg@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 917db484dc6a69969d317b3e57add4208a8d9d42 upstream.
In commit:
ec776ef6bbe1 ("x86/mm: Add support for the non-standard protected e820 type")
Christoph references the original patch I wrote implementing pmem support.
The intent of the 'max_pfn' changes in that commit were to enable persistent
memory ranges to be covered by the struct page memmap by default.
However, that approach was abandoned when Christoph ported the patches [1], and
that functionality has since been replaced by devm_memremap_pages().
In the meantime, this max_pfn manipulation is confusing kdump [2] that
assumes that everything covered by the max_pfn is "System RAM". This
results in kdump hanging or crashing.
[1]: https://lists.01.org/pipermail/linux-nvdimm/2015-March/000348.html
[2]: https://bugzilla.redhat.com/show_bug.cgi?id=1351098
So fix it.
Reported-by: Zhang Yi <yizhan@redhat.com>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Tested-by: Zhang Yi <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boaz Harrosh <boaz@plexistor.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-nvdimm@lists.01.org
Fixes: ec776ef6bbe1 ("x86/mm: Add support for the non-standard protected e820 type")
Link: http://lkml.kernel.org/r/147448744538.34910.11287693517367139607.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5e7307d9d5a340d2c9fabbe1cee137d4c682c71 upstream.
In some places, dump_backtrace() is called with a NULL tsk parameter,
e.g. in bug_handler() in arch/arm64, or indirectly via show_stack() in
core code. The expectation is that this is treated as if current were
passed instead of NULL. Similar is true of unwind_frame().
Commit a80a0eb70c358f8c ("arm64: make irq_stack_ptr more robust") didn't
take this into account. In dump_backtrace() it compares tsk against
current *before* we check if tsk is NULL, and in unwind_frame() we never
set tsk if it is NULL.
Due to this, we won't initialise irq_stack_ptr in either function. In
dump_backtrace() this results in calling dump_mem() for memory
immediately above the IRQ stack range, rather than for the relevant
range on the task stack. In unwind_frame we'll reject unwinding frames
on the IRQ stack.
In either case this results in incomplete or misleading backtrace
information, but is not otherwise problematic. The initial percpu areas
(including the IRQ stacks) are allocated in the linear map, and dump_mem
uses __get_user(), so we shouldn't access anything with side-effects,
and will handle holes safely.
This patch fixes the issue by having both functions handle the NULL tsk
case before doing anything else with tsk.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: a80a0eb70c358f8c ("arm64: make irq_stack_ptr more robust")
Acked-by: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ac0e89bb4744d3882ccd275f2416d9ce22f4e1e7 upstream.
We use logical negate where bitwise negate was intended. It means that
we never return -EINVAL here.
Fixes: ce11e48b7fdd ('KVM: PPC: E500: Add userspace debug stub support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0099b7701f5296a758d9e6b945ec96f96847cc2f upstream.
If the vgic hasn't been created and initialized, we shouldn't attempt to
look at its data structures or flush/sync anything to the GIC hardware.
This fixes an issue reported by Alexander Graf when using a userspace
irqchip.
Fixes: 0919e84c0fc1 ("KVM: arm/arm64: vgic-new: Add IRQ sync/flush framework")
Reported-by: Alexander Graf <agraf@suse.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6fe407f2d18a4f94216263f91cb7d1f08fa5887c upstream.
If userspace creates a PMU for the VCPU, but doesn't create an in-kernel
irqchip, then we end up in a nasty path where we try to take an
uninitialized spinlock, which can lead to all sorts of breakages.
Luckily, QEMU always creates the VGIC before the PMU, so we can
establish this as ABI and check for the VGIC in the PMU init stage.
This can be relaxed at a later time if we want to support PMU with a
userspace irqchip.
Cc: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91e4f1b6073dd680d86cdb7e42d7cccca9db39d8 upstream.
When a guest TLB entry is replaced by TLBWI or TLBWR, we only invalidate
TLB entries on the local CPU. This doesn't work correctly on an SMP host
when the guest is migrated to a different physical CPU, as it could pick
up stale TLB mappings from the last time the vCPU ran on that physical
CPU.
Therefore invalidate both user and kernel host ASIDs on other CPUs,
which will cause new ASIDs to be generated when it next runs on those
CPUs.
We're careful only to do this if the TLB entry was already valid, and
only for the kernel ASID where the virtual address it mapped is outside
of the guest user address range.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa73c3b25bd8d0d393dc6109a1dba3c2aef0451e upstream.
The MMCR2 register is available twice, one time with number 785
(privileged access), and one time with number 769 (unprivileged,
but it can be disabled completely). In former times, the Linux
kernel was using the unprivileged register 769 only, but since
commit 8dd75ccb571f3c92c ("powerpc: Use privileged SPR number
for MMCR2"), it uses the privileged register 785 instead.
The KVM-PR code then of course also switched to use the SPR 785,
but this is causing older guest kernels to crash, since these
kernels still access 769 instead. So to support older kernels
with KVM-PR again, we have to support register 769 in KVM-PR, too.
Fixes: 8dd75ccb571f3c92c48014b3dabd3d51a115ab41
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6a198bc60e6c980a56eca24d33dc7f29139f8ea upstream.
Early during boot topology_update_package_map() computes
logical_pkg_ids for all present processors.
Later, when processors are brought up, identify_cpu() updates
these values based on phys_pkg_id which is a function of
initial_apicid. On PV guests the latter may point to a
non-existing node, causing logical_pkg_ids to be set to -1.
Intel's RAPL uses logical_pkg_id (as topology_logical_package_id())
to index its arrays and therefore in this case will point to index
65535 (since logical_pkg_id is a u16). This could lead to either a
crash or may actually access random memory location.
As a workaround, we recompute topology during CPU bringup to reset
logical_pkg_id to a valid value.
(The reason for initial_apicid being bogus is because it is
initial_apicid of the processor from which the guest is launched.
This value is CPUID(1).EBX[31:24])
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 88003fb10f1fc606e1704611c62ceae95fd1d7da upstream.
This fixes a compile failure:
drivers/built-in.o: In function `wm8350_i2c_probe':
core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c'
Makefile:953: recipe for target 'vmlinux' failed
Fixes: 52b461b86a9f ("mfd: Add regmap cache support for wm8350")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a6dc644512fd083400a96ac4a035ac154fe6b8d upstream.
set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug. It's done
consistently so it won't cause a problem unless "irq" is more than 4.
Fixes: 70c6cce04066 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c2469bc03d569c49119db2cccb5cb3f0c6a5b33 upstream.
readl_poll_timeout() calls usleep_range(), but
regmap_atmel_hlcdc_reg_write() is called in atomic context (regmap
spinlock held).
Replace the readl_poll_timeout() call by readl_poll_timeout_atomic().
Fixes: ea31c0cf9b07 ("mfd: atmel-hlcdc: Implement config synchronization")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8dcc5ff8fcaf778bb57ab4448fedca9e381d088f upstream.
Member "status" of struct usb_sg_request is managed by usb core. A
spin lock is used to serialize the change of it. The driver could
check the value of req->status, but should avoid changing it without
the hold of the spinlock. Otherwise, it could cause race or error
in usb core.
This patch could be backported to stable kernels with version later
than v3.14.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
manufacturer ID
commit 8da08ca03b73593d5299893bf29fc08569c3fb5f upstream.
Currently, usb-line6 module exports an array of MIDI manufacturer ID and
usb-pod module uses it. However, the declaration is not the definition in
common header. The difference is explicit length of array. Although
compiler calculates it and everything goes well, it's better to use the
same representation between definition and declaration.
This commit fills the length of array for usb-line6 module. As a small
good sub-effect, this commit suppress below warnings from static analysis
by sparse v0.5.0.
sound/usb/line6/driver.c:274:43: error: cannot size expression
sound/usb/line6/driver.c:275:16: error: cannot size expression
sound/usb/line6/driver.c:276:16: error: cannot size expression
sound/usb/line6/driver.c:277:16: error: cannot size expression
Fixes: 705ececd1c60 ("Staging: add line6 usb driver")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb1a74b7bea17eea31915c4f76385cefe69d9795 upstream.
The DragonFly quirk added in 42e3121d90f4 ("ALSA: usb-audio: Add a more
accurate volume quirk for AudioQuest DragonFly") applies a custom dB map
on the volume control when its range is reported as 0..50 (0 .. 0.2dB).
However, there exists at least one other variant (hw v1.0c, as opposed
to the tested v1.2) which reports a different non-sensical volume range
(0..53) and the custom map is therefore not applied for that device.
This results in all of the volume change appearing close to 100% on
mixer UIs that utilize the dB TLV information.
Add a fallback case where no dB TLV is reported at all if the control
range is not 0..50 but still 0..N where N <= 1000 (3.9 dB). Also
restrict the quirk to only apply to the volume control as there is also
a mute control which would match the check otherwise.
Fixes: 42e3121d90f4 ("ALSA: usb-audio: Add a more accurate volume quirk for AudioQuest DragonFly")
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: David W <regulars@d-dub.org.uk>
Tested-by: David W <regulars@d-dub.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db68577966abc1aeae4ec597b3dcfa0d56e92041 upstream.
The pointer callbacks of ali5451 driver may return the value at the
boundary occasionally, and it results in the kernel warning like
snd_ali5451 0000:00:06.0: BUG: , pos = 16384, buffer size = 16384, period size = 1024
It seems that folding the position offset is enough for fixing the
warning and no ill-effect has been seen by that.
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5e6c88d28ccbe72bedee1fbf4f9fea4764208598 upstream.
Commit 50c763f8c1bac ("usb: dwc3: Set the ClearPendIN bit on Clear
Stall EP command") sets ClearPendIN bit for all IN endpoints of
v2.60a+ cores. This causes ClearStall command fails on 2.60+ cores
operating in HighSpeed mode.
In page 539 of 2.60a specification:
"When issuing Clear Stall command for IN endpoints in SuperSpeed
mode, the software must set the "ClearPendIN" bit to '1' to
clear any pending IN transcations, so that the device does not
expect any ACK TP from the host for the data sent earlier."
It's obvious that we only need to apply this rule to those IN
endpoints that currently operating in SuperSpeed mode.
Fixes: 50c763f8c1bac ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58bfea9532552d422bde7afa207e1a0f08dffa7d upstream.
In commit 27727df240c7 ("Avoid taking lock in NMI path with
CONFIG_DEBUG_TIMEKEEPING"), I changed the logic to open-code
the timekeeping_get_ns() function, but I forgot to include
the unit conversion from cycles to nanoseconds, breaking the
function's output, which impacts users like perf.
This results in bogus perf timestamps like:
swapper 0 [000] 253.427536: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.426573: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.426687: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.426800: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.426905: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.427022: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.427127: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.427239: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.427346: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 254.427463: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 255.426572: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
Instead of more reasonable expected timestamps like:
swapper 0 [000] 39.953768: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.064839: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.175956: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.287103: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.398217: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.509324: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.620437: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.731546: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.842654: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 40.953772: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
swapper 0 [000] 41.064881: 111111111 cpu-clock: ffffffff810a0de6 native_safe_halt+0x6 ([kernel.kallsyms])
Add the proper use of timekeeping_delta_to_ns() to convert
the cycle delta to nanoseconds as needed.
Thanks to Brendan and Alexei for finding this quickly after
the v4.8 release. Unfortunately the problematic commit has
landed in some -stable trees so they'll need this fix as
well.
Many apologies for this mistake. I'll be looking to add a
perf-clock sanity test to the kselftest timers tests soon.
Fixes: 27727df240c7 "timekeeping: Avoid taking lock in NMI path with CONFIG_DEBUG_TIMEKEEPING"
Reported-by: Brendan Gregg <bgregg@netflix.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Tested-and-reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1475636148-26539-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f38a8b9a45833495dc878c335c5431cd98a16ed upstream.
When cxl removes a vPHB, it's possible that the pci_controller may be freed
before all references to the devices on the vPHB have been released. This
in turn causes an invalid memory access when the devices are eventually
released, as pcibios_release_device() attempts to call the phb's
release_device hook.
In cxl_pci_vphb_remove(), remove the existing call to
pcibios_free_controller(). Instead, use
pcibios_free_controller_deferred() to free the pci_controller after all
devices have been released. Export pci_set_host_bridge_release() so we can
do this.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2dd9c11b9d4dfbd6c070eab7b81197f65e82f1a0 upstream.
This patch leverages 'struct pci_host_bridge' from the PCI subsystem
in order to free the pci_controller only after the last reference to
its devices is dropped (avoiding an oops in pcibios_release_device()
if the last reference is dropped after pcibios_free_controller()).
The patch relies on pci_host_bridge.release_fn() (and .release_data),
which is called automatically by the PCI subsystem when the root bus
is released (i.e., the last reference is dropped). Those fields are
set via pci_set_host_bridge_release() (e.g. in the platform-specific
implementation of pcibios_root_bridge_prepare()).
It introduces the 'pcibios_free_controller_deferred()' .release_fn()
and it expects .release_data to hold a pointer to the pci_controller.
The function implictly calls 'pcibios_free_controller()', so an user
must *NOT* explicitly call it if using the new _deferred() callback.
The functionality is enabled for pseries (although it isn't platform
specific, and may be used by cxl).
Details on not-so-elegant design choices:
- Use 'pci_host_bridge.release_data' field as pointer to associated
'struct pci_controller' so *not* to 'pci_bus_to_host(bridge->bus)'
in pcibios_free_controller_deferred().
That's because pci_remove_root_bus() sets 'host_bridge->bus = NULL'
(so, if the last reference is released after pci_remove_root_bus()
runs, which eventually reaches pcibios_free_controller_deferred(),
that would hit a null pointer dereference).
The cxl/vphb.c code calls pci_remove_root_bus(), and the cxl folks
are interested in this fix.
Test-case #1 (hold references)
# ls -ld /sys/block/sd* | grep -m1 0021:01:00.0
<...> /sys/block/sdaa -> ../devices/pci0021:01/0021:01:00.0/<...>
# ls -ld /sys/block/sd* | grep -m1 0021:01:00.1
<...> /sys/block/sdab -> ../devices/pci0021:01/0021:01:00.1/<...>
# cat >/dev/sdaa & pid1=$!
# cat >/dev/sdab & pid2=$!
# drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r
Validating PHB DLPAR capability...yes.
[ 594.306719] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01
[ 594.306738] pci_hp_remove_devices: Removing 0021:01:00.0...
...
[ 598.236381] pci_hp_remove_devices: Removing 0021:01:00.1...
...
[ 611.972077] pci_bus 0021:01: busn_res: [bus 01-ff] is released
[ 611.972140] rpadlpar_io: slot PHB 33 removed
# kill -9 $pid1
# kill -9 $pid2
[ 632.918088] pcibios_free_controller_deferred: domain 33, dynamic 1
Test-case #2 (don't hold references)
# drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r
Validating PHB DLPAR capability...yes.
[ 916.357363] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01
[ 916.357386] pci_hp_remove_devices: Removing 0021:01:00.0...
...
[ 920.566527] pci_hp_remove_devices: Removing 0021:01:00.1...
...
[ 933.955873] pci_bus 0021:01: busn_res: [bus 01-ff] is released
[ 933.955977] pcibios_free_controller_deferred: domain 33, dynamic 1
[ 933.955999] rpadlpar_io: slot PHB 33 removed
Suggested-By: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 0eec880966e77bdbee0112989a2be67d92e39929 upstream.
HP Spectre x360 with CX20724 codec has two speaker outputs while the
BIOS sets up only the bottom one (NID 0x17) and disables the top one
(NID 0x1d).
This patch adds a fixup simply defining the proper pincfg for NID 0x1d
so that the top speaker works as is.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=169071
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3f640970a41429f0a076c01270bbd014c9eae61c upstream.
One of the laptops has the codec ALC256 on it, applying the
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE can fix the problem, the rest
of laptops have the codec ALC295 on them, they are similar to machines
with ALC225, applying the ALC269_FIXUP_DELL1_MIC_NO_PRESENCE can fix
the problem.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 392c9da24a994f238c5d7ea611c6245be4617014 upstream.
We have two new Dell laptop models, they have the same ALC255 pin
definition, but not in the pin quirk table yet, as a result, the
headset microphone can't work. After adding the definition in the
table, the headset microphone works well.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab21b63e8aedfc73565dd9cdd51eb338341177cb upstream.
This reverts commit e6c7efdcb76f11b04e3d3f71c8d764ab75c9423b.
Turns out it was totally wrong. The memory is supposed to be bound to
the kref, as the original code was doing correctly, not the
device/driver binding as the devm_kzalloc() would cause.
This fixes an oops when read would be called after the device was
unbound from the driver.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit decc5360f23e9efe0252094f47f57f254dcbb3a9 upstream.
Signed-off-by: Kyle Jones <kyle@kf5jwc.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 238b7bd91b16d5a08326f858db42229b212e53d8 upstream.
In v_recv_cmd_submit(), urb_p->urb->pipe has the type unsigned int
(which is 32-bit long on x86_64) but 11<<30 results in a 34-bit integer.
Therefore the 2 leading bits are truncated and
urb_p->urb->pipe &= ~(11 << 30);
has the same meaning as
urb_p->urb->pipe &= ~(3 << 30);
This second statement seems to be how the code was intended to be
written, as PIPE_ constants have values between 0 and 3.
The overflow has been detected with a clang warning:
drivers/usb/usbip/vudc_rx.c:145:27: warning: signed shift result
(0x2C0000000) requires 35 bits to represent, but 'int' only has 32
bits [-Wshift-overflow]
urb_p->urb->pipe &= ~(11 << 30);
~~ ^ ~~
Fixes: 79c02cb1fd5c ("usbip: vudc: Add vudc_rx")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc1e2c8ea85e109acf09e74789e9b852f6eed251 upstream.
Commit 367e8560e8d7a62d96e9b1d644028a3816e04206 introduced a bug
in fbtft-core where fps is always 0, this is because variable
update_time is not assigned correctly.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Fixes: 367e8560e8d7 ("Staging: fbtbt: Replace timespec with ktime_t")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2fae9e5a7babada041e2e161699ade2447a01989 upstream.
This patch fixes a NULL pointer dereference caused by a race codition in
the probe function of the legousbtower driver. It re-structures the
probe function to only register the interface after successfully reading
the board's firmware ID.
The probe function does not deregister the usb interface after an error
receiving the devices firmware ID. The device file registered
(/dev/usb/legousbtower%d) may be read/written globally before the probe
function returns. When tower_delete is called in the probe function
(after an r/w has been initiated), core dev structures are deleted while
the file operation functions are still running. If the 0 address is
mappable on the machine, this vulnerability can be used to create a
Local Priviege Escalation exploit via a write-what-where condition by
remapping dev->interrupt_out_buffer in tower_write. A forged USB device
and local program execution would be required for LPE. The USB device
would have to delay the control message in tower_probe and accept
the control urb in tower_open whilst guest code initiated a write to the
device file as tower_delete is called from the error in tower_probe.
This bug has existed since 2003. Patch tested by emulated device.
Reported-by: James Patrick-Evans <james@jmp-e.com>
Tested-by: James Patrick-Evans <james@jmp-e.com>
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7efb367320f56fc4d549875b6f3a6940018ef2e5 upstream.
bio_alloc() can allocate a bio with at most BIO_MAX_PAGES (256) vector
entries. However, the incoming bio may have more vector entries if it
was allocated by other means. For example, bcache submits bios with
more than BIO_MAX_PAGES entries. This results in bio_alloc() failure.
To avoid the failure, change the code so that it allocates bio with at
most BIO_MAX_PAGES entries. If the incoming bio has more entries,
bio_add_page() will fail and a new bio will be allocated - the code that
handles bio_add_page() failure already exists in the dm-log-writes
target.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22f6b4d34fcf039c63a94e7670e0da24f8575a5a upstream.
This ensures that do_mmap() won't implicitly make AIO memory mappings
executable if the READ_IMPLIES_EXEC personality flag is set. Such
behavior is problematic because the security_mmap_file LSM hook doesn't
catch this case, potentially permitting an attacker to bypass a W^X
policy enforced by SELinux.
I have tested the patch on my machine.
To test the behavior, compile and run this:
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/personality.h>
#include <linux/aio_abi.h>
#include <err.h>
#include <stdlib.h>
#include <stdio.h>
#include <sys/syscall.h>
int main(void) {
personality(READ_IMPLIES_EXEC);
aio_context_t ctx = 0;
if (syscall(__NR_io_setup, 1, &ctx))
err(1, "io_setup");
char cmd[1000];
sprintf(cmd, "cat /proc/%d/maps | grep -F '/[aio]'",
(int)getpid());
system(cmd);
return 0;
}
In the output, "rw-s" is good, "rwxs" is bad.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 422eac3f7deae34dbaffd08e03e27f37a5394a56 upstream.
On my Lenovo x250 the following situation occurs:
[18697.813871] tpm_crb MSFT0101:00: can't request region for resource
[mem 0xacdff080-0xacdfffff]
The mapping of the control area overlaps the mapping of the command
buffer. The control area is mapped over page, which is not right. It
should mapped over sizeof(struct crb_control_area).
Fixing this issue unmasks another issue. Command and response buffers
can overlap and they do interleave on this machine. According to the PTP
specification the overlapping means that they are mapped to the same
buffer.
The commit has been also on a Haswell NUC where things worked before
applying this fix so that the both code paths for response buffer
initialization are tested.
Cc: stable@vger.kernel.org
Fixes: 1bd047be37d9 ("tpm_crb: Use devm_ioremap_resource")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14ddfbf488a0223b19abf7e4634e6e676a91a12d upstream.
The iomem resource is needed only temporarily so it is better to pass
it on instead of storing it permanently. Named the variable as io_res
so that the code better documents itself.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d9f179877e50ae2681fe7b0b83e0d9f63b6165ad upstream.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee3da804ad1b1dd4c766199a6e8443542b0aaaef upstream.
Set the source mac address in the FTE when L2 specification
is provided.
Fixes: 038d2ef87572 ('IB/mlx5: Add flow steering support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7fae6655a0c897875bd34501ec092232b526d3e4 upstream.
MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.
Fixes: d603c809ef91 ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: David Chang <dchang@suse.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8ec07bf8a8b57d6c58927a16a0a22c0115cf2855 upstream.
When sending QP1 MAD packets which use a GRH, the source GID
(which consists of the 64-bit subnet prefix, and the 64 bit port GUID)
must be included in the packet GRH.
For SR-IOV, a GID cache is used, since the source GID needs to be the
slave's source GID, and not the Hypervisor's GID. This cache also
included a subnet_prefix. Unfortunately, the subnet_prefix field in
the cache was never initialized (to the default subnet prefix 0xfe80::0).
As a result, this field remained all zeroes. Therefore, when SR-IOV
was active, all QP1 packets which included a GRH had a source GID
subnet prefix of all-zeroes.
However, the subnet-prefix should initially be 0xfe80::0 (the default
subnet prefix). In addition, if OpenSM modifies a port's subnet prefix,
the new subnet prefix must be used in the GRH when sending QP1 packets.
To fix this we now initialize the subnet prefix in the SR-IOV GID cache
to the default subnet prefix. We update the cached value if/when OpenSM
modifies the port's subnet prefix. We take this cached value when sending
QP1 packets when SR-IOV is active.
Note that the value is stored as an atomic64. This eliminates any need
for locking when the subnet prefix is being updated.
Note also that we depend on the FW generating the "port management change"
event for tracking subnet-prefix changes performed by OpenSM. If running
early FW (before 2.9.4630), subnet prefix changes will not be tracked (but
the default subnet prefix still will be stored in the cache; therefore
users who do not modify the subnet prefix will not have a problem).
IF there is a need for such tracking also for early FW, we will add that
capability in a subsequent patch.
Fixes: 1ffeb2eb8be9 ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit baa0be7026e2f7d1d40bfd45909044169e9e3c68 upstream.
The indentation in the QP1 GRH flow in procedure build_mlx_header is
really confusing. Fix it, in preparation for a commit which touches
this code.
Fixes: 1ffeb2eb8be9 ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Greg Kroah-Hartman
Jarkko Sakkinen
Miklos Szeredi
Christophe Jaillet
Linus Walleij
Grzegorz Jaszczyk
Josh Poimboeuf
Nicolas Iooss
Prarit Bhargava
Denys Vlasenko
Dave Hansen
Mika Westerberg
Dan Williams
Mark Rutland
Dan Carpenter
Christoffer Dall
James Hogan
Thomas Huth
Boris Ostrovsky
Uwe Kleine-König
Boris Brezillon
Lu Baolu
Takashi Sakamoto
Anssi Hannula
Takashi Iwai
John Stultz
Andrew Donnellan
Mauricio Faria de Oliveira
Hui Wang
Kyle Jones
Ksenija Stanojevic
Mikulas Patocka
Jann Horn
Marek Lindner
Maor Gottlieb
Noa Osherovich
Jack Morgenstein