aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts')
-rw-r--r--arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts428
1 files changed, 211 insertions, 217 deletions
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index c14205cd6bf5..533ed523888d 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -122,222 +122,6 @@
power-off-delay-us = <10>;
};
- soc {
- spi0: spi@f7106000 {
- status = "ok";
- };
-
- i2c0: i2c@f7100000 {
- status = "ok";
- };
-
- i2c1: i2c@f7101000 {
- status = "ok";
- };
-
- uart1: uart@f7111000 {
- assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
- assigned-clock-rates = <150000000>;
- status = "ok";
-
- bluetooth {
- compatible = "ti,wl1835-st";
- enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- clocks = <&pmic>;
- clock-names = "ext_clock";
- };
- };
-
- uart2: uart@f7112000 {
- status = "ok";
- };
-
- uart3: uart@f7113000 {
- status = "ok";
- };
-
- /*
- * Legend: proper name = the GPIO line is used as GPIO
- * NC = not connected (not routed from the SoC)
- * "[PER]" = pin is muxed for peripheral (not GPIO)
- * "" = no idea, schematic doesn't say, could be
- * unrouted (not connected to any external pin)
- * LSEC = Low Speed External Connector
- * HSEC = High Speed External Connector
- *
- * Pin assignments taken from LeMaker and CircuitCo Schematics
- * Rev A1.
- *
- * For the lines routed to the external connectors the
- * lines are named after the 96Boards CE Specification 1.0,
- * Appendix "Expansion Connector Signal Description".
- *
- * When the 96Board naming of a line and the schematic name of
- * the same line are in conflict, the 96Board specification
- * takes precedence, which means that the external UART on the
- * LSEC is named UART0 while the schematic and SoC names this
- * UART2. This is only for the informational lines i.e. "[FOO]",
- * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
- * ones actually used for GPIO.
- */
- gpio0: gpio@f8011000 {
- gpio-line-names = "PWR_HOLD", "DSI_SEL",
- "USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
- "PWRON_DET", "5V_HUB_EN";
- };
-
- gpio1: gpio@f8012000 {
- gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
- "WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
- };
-
- gpio2: gpio@f8013000 {
- gpio-line-names =
- "GPIO-A", /* LSEC Pin 23: GPIO2_0 */
- "GPIO-B", /* LSEC Pin 24: GPIO2_1 */
- "GPIO-C", /* LSEC Pin 25: GPIO2_2 */
- "GPIO-D", /* LSEC Pin 26: GPIO2_3 */
- "GPIO-E", /* LSEC Pin 27: GPIO2_4 */
- "USB_ID_DET", "USB_VBUS_DET",
- "GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
- };
-
- gpio3: gpio@f8014000 {
- gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
- "WLAN_ACTIVE", "NC", "NC";
- };
-
- gpio4: gpio@f7020000 {
- gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
- "USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
- };
-
- gpio5: gpio@f7021000 {
- gpio-line-names = "NC", "NC",
- "[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
- "[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
- "[AUX_SSI1]", "NC",
- "[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
- "[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
- };
-
- gpio6: gpio@f7022000 {
- gpio-line-names =
- "[SPI0_DIN]", /* Pin 10: SPI0_DI */
- "[SPI0_DOUT]", /* Pin 14: SPI0_DO */
- "[SPI0_CS]", /* Pin 12: SPI0_CS_N */
- "[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
- "NC", "NC", "NC",
- "GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
- };
-
- gpio7: gpio@f7023000 {
- gpio-line-names = "NC", "NC", "NC", "NC",
- "[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
- "[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
- "NC", "NC";
- };
-
- gpio8: gpio@f7024000 {
- gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
- "", "", "", "", "", "";
- };
-
- gpio9: gpio@f7025000 {
- gpio-line-names = "",
- "GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
- "GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
- "NC", "NC", "NC", "NC", "[ISP_CCLK0]";
- };
-
- gpio10: gpio@f7026000 {
- gpio-line-names = "BOOT_SEL",
- "[ISP_CCLK1]",
- "GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
- "GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
- "NC", "NC",
- "[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
- "[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
- };
-
- gpio11: gpio@f7027000 {
- gpio-line-names =
- "[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
- "[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
- "", "NC", "NC", "NC", "", "";
- };
-
- gpio12: gpio@f7028000 {
- gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
- "[BT_PCM_DO]",
- "NC", "NC", "NC", "NC",
- "GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
- };
-
- gpio13: gpio@f7029000 {
- gpio-line-names = "[UART0_RX]", "[UART0_TX]",
- "[BT_UART1_CTS]", "[BT_UART1_RTS]",
- "[BT_UART1_RX]", "[BT_UART1_TX]",
- "[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
- "[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
- };
-
- gpio14: gpio@f702a000 {
- gpio-line-names =
- "[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
- "[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
- "[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
- "[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
- "[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
- "[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
- "[I2C2_SCL]", "[I2C2_SDA]";
- };
-
- gpio15: gpio@f702b000 {
- gpio-line-names = "", "", "", "", "", "", "NC", "";
- };
-
- /* GPIO blocks 16 thru 19 do not appear to be routed to pins */
-
- dwmmc_0: dwmmc0@f723d000 {
- cap-mmc-highspeed;
- non-removable;
- bus-width = <0x8>;
- vmmc-supply = <&ldo19>;
- };
-
- dwmmc_1: dwmmc1@f723e000 {
- card-detect-delay = <200>;
- cap-sd-highspeed;
- sd-uhs-sdr12;
- sd-uhs-sdr25;
- sd-uhs-sdr50;
- vqmmc-supply = <&ldo7>;
- vmmc-supply = <&ldo10>;
- bus-width = <0x4>;
- disable-wp;
- cd-gpios = <&gpio1 0 1>;
- };
-
- dwmmc_2: dwmmc2@f723f000 {
- bus-width = <0x4>;
- non-removable;
- cap-power-off-card;
- vmmc-supply = <&reg_vdd_3v3>;
- mmc-pwrseq = <&wl1835_pwrseq>;
-
- #address-cells = <0x1>;
- #size-cells = <0x0>;
- wlcore: wlcore@2 {
- compatible = "ti,wl1835";
- reg = <2>; /* sdio func num */
- /* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
- interrupt-parent = <&gpio1>;
- interrupts = <3 IRQ_TYPE_EDGE_RISING>;
- };
- };
- };
-
leds {
compatible = "gpio-leds";
@@ -480,10 +264,26 @@
};
};
+&uart1 {
+ assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
+ assigned-clock-rates = <150000000>;
+ status = "ok";
+
+ bluetooth {
+ compatible = "ti,wl1835-st";
+ enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ clocks = <&pmic>;
+ clock-names = "ext_clock";
+ };
+};
+
&uart2 {
+ status = "ok";
label = "LS-UART0";
};
+
&uart3 {
+ status = "ok";
label = "LS-UART1";
};
@@ -506,6 +306,196 @@
};
};
+&dwmmc_0 {
+ cap-mmc-highspeed;
+ non-removable;
+ bus-width = <0x8>;
+ vmmc-supply = <&ldo19>;
+};
+
+&dwmmc_1 {
+ card-detect-delay = <200>;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ vqmmc-supply = <&ldo7>;
+ vmmc-supply = <&ldo10>;
+ bus-width = <0x4>;
+ disable-wp;
+ cd-gpios = <&gpio1 0 1>;
+};
+
+&dwmmc_2 {
+ bus-width = <0x4>;
+ non-removable;
+ cap-power-off-card;
+ vmmc-supply = <&reg_vdd_3v3>;
+ mmc-pwrseq = <&wl1835_pwrseq>;
+
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>; /* sdio func num */
+ /* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+/*
+ * Legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (not routed from the SoC)
+ * "[PER]" = pin is muxed for peripheral (not GPIO)
+ * "" = no idea, schematic doesn't say, could be
+ * unrouted (not connected to any external pin)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Pin assignments taken from LeMaker and CircuitCo Schematics
+ * Rev A1.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART2. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+&gpio0 {
+ gpio-line-names = "PWR_HOLD", "DSI_SEL",
+ "USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
+ "PWRON_DET", "5V_HUB_EN";
+};
+
+&gpio1 {
+ gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
+ "WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "GPIO-A", /* LSEC Pin 23: GPIO2_0 */
+ "GPIO-B", /* LSEC Pin 24: GPIO2_1 */
+ "GPIO-C", /* LSEC Pin 25: GPIO2_2 */
+ "GPIO-D", /* LSEC Pin 26: GPIO2_3 */
+ "GPIO-E", /* LSEC Pin 27: GPIO2_4 */
+ "USB_ID_DET", "USB_VBUS_DET",
+ "GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
+};
+
+&gpio3 {
+ gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
+ "WLAN_ACTIVE", "NC", "NC";
+};
+
+&gpio4 {
+ gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
+ "USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
+};
+
+&gpio5 {
+ gpio-line-names = "NC", "NC",
+ "[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
+ "[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
+ "[AUX_SSI1]", "NC",
+ "[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
+ "[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
+};
+
+&gpio6 {
+ gpio-line-names =
+ "[SPI0_DIN]", /* Pin 10: SPI0_DI */
+ "[SPI0_DOUT]", /* Pin 14: SPI0_DO */
+ "[SPI0_CS]", /* Pin 12: SPI0_CS_N */
+ "[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
+ "NC", "NC", "NC",
+ "GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
+};
+
+&gpio7 {
+ gpio-line-names = "NC", "NC", "NC", "NC",
+ "[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
+ "[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
+ "NC", "NC";
+};
+
+&gpio8 {
+ gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
+ "", "", "", "", "", "";
+};
+
+&gpio9 {
+ gpio-line-names = "",
+ "GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
+ "GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
+ "NC", "NC", "NC", "NC", "[ISP_CCLK0]";
+};
+
+&gpio10 {
+ gpio-line-names = "BOOT_SEL",
+ "[ISP_CCLK1]",
+ "GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
+ "GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
+ "NC", "NC",
+ "[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
+ "[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
+};
+
+&gpio11 {
+ gpio-line-names =
+ "[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
+ "[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
+ "", "NC", "NC", "NC", "", "";
+};
+
+&gpio12 {
+ gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
+ "[BT_PCM_DO]",
+ "NC", "NC", "NC", "NC",
+ "GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
+};
+
+&gpio13 {
+ gpio-line-names = "[UART0_RX]", "[UART0_TX]",
+ "[BT_UART1_CTS]", "[BT_UART1_RTS]",
+ "[BT_UART1_RX]", "[BT_UART1_TX]",
+ "[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
+ "[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
+};
+
+&gpio14 {
+ gpio-line-names =
+ "[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
+ "[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
+ "[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
+ "[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
+ "[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
+ "[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
+ "[I2C2_SCL]", "[I2C2_SDA]";
+};
+
+&gpio15 {
+ gpio-line-names = "", "", "", "", "", "", "NC", "";
+};
+
+/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
+
+
+&i2c0 {
+ status = "ok";
+};
+
+&i2c1 {
+ status = "ok";
+};
+
&i2c2 {
#address-cells = <1>;
#size-cells = <0>;
@@ -516,7 +506,7 @@
reg = <0x39>;
interrupt-parent = <&gpio1>;
interrupts = <1 2>;
- pd-gpio = <&gpio0 4 0>;
+ pd-gpios = <&gpio0 4 0>;
adi,dsi-lanes = <4>;
#sound-dai-cells = <0>;
@@ -549,3 +539,7 @@
};
};
};
+
+&spi0 {
+ status = "ok";
+};