diff options
Diffstat (limited to 'arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts')
-rw-r--r-- | arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 273 |
1 files changed, 0 insertions, 273 deletions
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts deleted file mode 100644 index d729b7c705db..000000000000 --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ /dev/null @@ -1,273 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> - * - * Based on sun8i-h3-bananapi-m2-plus.dts, which is: - * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org> - */ - -/dts-v1/; -#include "sun8i-h3.dtsi" -#include "sunxi-common-regulators.dtsi" - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> - -/ { - model = "Banana Pi BPI-M2-Zero"; - compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus"; - - aliases { - serial0 = &uart0; - serial1 = &uart1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - connector { - compatible = "hdmi-connector"; - type = "c"; - - port { - hdmi_con_in: endpoint { - remote-endpoint = <&hdmi_out_con>; - }; - }; - }; - - leds { - compatible = "gpio-leds"; - - pwr_led { - label = "bananapi-m2-zero:red:pwr"; - gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */ - default-state = "on"; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - - switch-4 { - label = "power"; - linux,code = <KEY_POWER>; - gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; - wakeup-source; - }; - }; - - reg_vdd_cpux: vdd-cpux-regulator { - compatible = "regulator-gpio"; - regulator-name = "vdd-cpux"; - regulator-type = "voltage"; - regulator-boot-on; - regulator-always-on; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1300000>; - regulator-ramp-delay = <50>; /* 4ms */ - - gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */ - enable-active-high; - gpios-states = <0x1>; - states = <1100000 0>, <1300000 1>; - }; - - reg_vcc_dram: vcc-dram { - compatible = "regulator-fixed"; - regulator-name = "vcc-dram"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - regulator-always-on; - regulator-boot-on; - enable-active-high; - gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ - vin-supply = <®_vcc5v0>; - }; - - reg_vcc1v2: vcc1v2 { - compatible = "regulator-fixed"; - regulator-name = "vcc1v2"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - regulator-boot-on; - enable-active-high; - gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ - vin-supply = <®_vcc5v0>; - }; - - poweroff { - compatible = "regulator-poweroff"; - cpu-supply = <®_vcc1v2>; - }; - - wifi_pwrseq: wifi_pwrseq { - compatible = "mmc-pwrseq-simple"; - reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ - clocks = <&rtc CLK_OSC32K_FANOUT>; - clock-names = "ext_clock"; - }; -}; - -&cpu0 { - cpu-supply = <®_vdd_cpux>; -}; - -&de { - status = "okay"; -}; - -&ehci0 { - status = "okay"; -}; - -&hdmi { - status = "okay"; -}; - -&hdmi_out { - hdmi_out_con: endpoint { - remote-endpoint = <&hdmi_con_in>; - }; -}; - -&mmc0 { - vmmc-supply = <®_vcc3v3>; - bus-width = <4>; - /* - * On the production batch of this board the card detect GPIO is - * high active (card inserted), although on the early samples it's - * low active. - */ - cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ - status = "okay"; -}; - -&mmc1 { - vmmc-supply = <®_vcc3v3>; - vqmmc-supply = <®_vcc3v3>; - mmc-pwrseq = <&wifi_pwrseq>; - bus-width = <4>; - non-removable; - status = "okay"; - - brcmf: wifi@1 { - reg = <1>; - compatible = "brcm,bcm4329-fmac"; - interrupt-parent = <&pio>; - interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ - interrupt-names = "host-wake"; - }; -}; - -&ohci0 { - status = "okay"; -}; - -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pa_pins>; - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; - uart-has-rtscts; - status = "okay"; - - bluetooth { - compatible = "brcm,bcm43438-bt"; - max-speed = <1500000>; - clocks = <&rtc CLK_OSC32K_FANOUT>; - clock-names = "lpo"; - vbat-supply = <®_vcc3v3>; - vddio-supply = <®_vcc3v3>; - device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */ - host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */ - shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ - }; - -}; - -&pio { - gpio-line-names = - /* PA */ - "CON2-P13", "CON2-P11", "CON2-P22", "CON2-P15", - "CON3-P03", "CON3-P02", "CON2-P07", "CON2-P29", - "CON2-P31", "CON2-P33", "CON2-P35", "CON2-P05", - "CON2-P03", "CON2-P08", "CON2-P10", "CON2-P16", - "CON2-P12", "CON2-P37", "CON2-P28", "CON2-P27", - "CON2-P40", "CON2-P38", "", "", - "", "", "", "", "", "", "", "", - - /* PB */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - - /* PC */ - "CON2-P19", "CON2-P21", "CON2-P23", "CON2-P24", - "CON2-P18", "", "", "CON2-P26", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - - /* PD */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "CSI-PWR-EN", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - - /* PE */ - "CN3-P17", "CN3-P13", "CN3-P09", "CN3-P07", - "CN3-P19", "CN3-P21", "CN3-P22", "CN3-P20", - "CN3-P18", "CN3-P16", "CN3-P14", "CN3-P12", - "CN3-P05", "CN3-P03", "CN3-P06", "CN3-P08", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - - /* PF */ - "SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3", - "SDC0-D2", "SDC0-DET", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - - /* PG */ - "WL-SDIO-CLK", "WL-SDIO-CMD", "WL-SDIO-D0", "WL-SDIO-D1", - "WL-SDIO-D2", "WL-SDIO-D3", "BT-UART-TX", "BT-UART-RX", - "BT-UART-RTS", "BT-UART-CTS", "WL-WAKE-AP", "BT-WAKE-AP", - "BT-RST-N", "AP-WAKE-BT", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; -}; - -&r_pio { - gpio-line-names = - /* PL */ - "", "CPUX-SET", "CON2-P32", "POWER-KEY", "CON2-P36", - "VCC-IO-EN", "USB0-ID", "WL-PWR-EN", - "PWR-STB", "PWR-DRAM", "PWR-LED", "IR-RX", "", "", "", "", - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", ""; -}; - -&usb_otg { - dr_mode = "otg"; - status = "okay"; -}; - -&usbphy { - usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ - /* - * There're two micro-USB connectors, one is power-only and another is - * OTG. The Vbus of these two connectors are connected together, so - * the external USB device will be powered just by the power input - * from the power-only USB port. - */ - status = "okay"; -}; |