diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi | 289 |
1 files changed, 0 insertions, 289 deletions
diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi deleted file mode 100644 index 37e59403c01f..000000000000 --- a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi +++ /dev/null @@ -1,289 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Device Tree for the TVK1281618 R2 user interface board (UIB) - */ - -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/input/input.h> - -/ { - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>; - - button@139 { - /* Proximity sensor */ - gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; - linux,code = <11>; /* SW_FRONT_PROXIMITY */ - label = "SFH7741 Proximity Sensor"; - }; - button@145 { - /* Hall sensor */ - gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; - linux,code = <0>; /* SW_LID */ - label = "HED54XXU11 Hall Effect Sensor"; - }; - }; - - soc { - i2c@80004000 { - tc35893@44 { - compatible = "toshiba,tc35893"; - reg = <0x44>; - interrupt-parent = <&gpio6>; - interrupts = <26 IRQ_TYPE_EDGE_RISING>; - pinctrl-names = "default"; - pinctrl-0 = <&tc35893_tvk_mode>; - - interrupt-controller; - #interrupt-cells = <1>; - status = "disabled"; - - tc3589x_gpio { - compatible = "toshiba,tc3589x-gpio"; - interrupts = <0>; - - interrupt-controller; - #interrupt-cells = <2>; - gpio-controller; - #gpio-cells = <2>; - }; - tc3589x_keypad { - compatible = "toshiba,tc3589x-keypad"; - interrupts = <6>; - debounce-delay-ms = <4>; - keypad,num-columns = <8>; - keypad,num-rows = <8>; - linux,no-autorepeat; - wakeup-source; - linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>, - <MATRIX_KEY(4, 1, KEY_HOME)>, - <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>, - <MATRIX_KEY(4, 2, KEY_EMAIL)>, - <MATRIX_KEY(3, 3, KEY_RIGHT)>, - <MATRIX_KEY(2, 5, KEY_BACKSPACE)>, - <MATRIX_KEY(6, 7, KEY_MENU)>, - <MATRIX_KEY(5, 0, KEY_ENTER)>, - <MATRIX_KEY(4, 3, KEY_0)>, - <MATRIX_KEY(3, 4, KEY_DOT)>, - <MATRIX_KEY(5, 2, KEY_UP)>, - <MATRIX_KEY(3, 5, KEY_DOWN)>, - <MATRIX_KEY(4, 5, KEY_SEND)>, - <MATRIX_KEY(0, 5, KEY_BACK)>, - <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>, - <MATRIX_KEY(1, 3, KEY_SPACE)>, - <MATRIX_KEY(7, 6, KEY_LEFT)>, - <MATRIX_KEY(5, 5, KEY_SEARCH)>; - }; - }; - }; - - i2c@80128000 { - accelerometer@18 { - /* Accelerometer */ - compatible = "st,lsm303dlh-accel"; - st,drdy-int-pin = <1>; - drive-open-drain; - reg = <0x18>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; - */ - mount-matrix = "0", "1", "0", - "1", "0", "0", - "0", "0", "-1"; - }; - magnetometer@1e { - /* Magnetometer */ - compatible = "st,lsm303dlh-magn"; - reg = <0x1e>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; - */ - }; - accelerometer@1c { - /* Accelerometer */ - compatible = "st,lis331dl-accel"; - st,drdy-int-pin = <1>; - reg = <0x1c>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; - interrupt-parent = <&gpio2>; - /* INT2 would need to be open drain */ - interrupts = <18 IRQ_TYPE_EDGE_RISING>, - <19 IRQ_TYPE_EDGE_RISING>; - mount-matrix = "0", "-1", "0", - "-1", "0", "0", - "0", "0", "-1"; - }; - magnetometer@f { - /* Magnetometer */ - compatible = "asahi-kasei,ak8974"; - reg = <0x0f>; - avdd-supply = <&ab8500_ldo_aux1_reg>; - dvdd-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&gyro_magn_tvk_mode>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>; - */ - }; - gyroscope@68 { - /* Gyroscope */ - compatible = "st,l3g4200d-gyro"; - st,drdy-int-pin = <2>; - reg = <0x68>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&gyro_magn_tvk_mode>; - interrupts-extended = - <&gpio1 0 IRQ_TYPE_EDGE_RISING>, - <&gpio0 31 IRQ_TYPE_EDGE_RISING>; - }; - pressure@5c { - /* Barometer/pressure sensor */ - compatible = "st,lps001wp-press"; - reg = <0x5c>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - }; - }; - i2c@80110000 { - synaptics@4b { - /* Synaptics RMI4 TM1217 touchscreen */ - compatible = "syna,rmi4-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x4b>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&synaptics_tvk_mode>; - interrupt-parent = <&gpio2>; - interrupts = <20 IRQ_TYPE_EDGE_FALLING>; - - rmi4-f01@1 { - reg = <0x1>; - syna,nosleep = <1>; - }; - rmi4-f11@11 { - reg = <0x11>; - syna,sensor-type = <1>; - /* This is a landscape display */ - touchscreen-swapped-x-y; - }; - }; - }; - mcde@a0350000 { - status = "okay"; - - dsi@a0351000 { - panel { - compatible = "samsung,s6d16d0"; - reg = <0>; - vdd1-supply = <&ab8500_ldo_aux1_reg>; - reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; - }; - }; - }; - pinctrl { - prox { - prox_tvk_mode: prox_tvk { - tvk_cfg { - pins = "GPIO217_AH12"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - hall { - hall_tvk_mode: hall_tvk { - tvk_cfg { - pins = "GPIO145_C13"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - tc35893 { - /* IRQ from the TC35893 */ - tc35893_tvk_mode: tc35893_tvk { - tvk_cfg { - pins = "GPIO218_AH11"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - accelerometer { - accel_tvk_mode: accel_tvk { - /* Accelerometer interrupt lines 1 & 2 */ - tvk_cfg { - pins = "GPIO82_C1", "GPIO83_D3"; - ste,config = <&gpio_in_pd>; - }; - }; - }; - gyroscope { - /* - * These lines are shared between Gyroscope l3g400dh - * and AK8974 magnetometer. - */ - gyro_magn_tvk_mode: gyro_magn_tvk { - /* GPIO 31 used for INT pull down the line */ - tvk_cfg1 { - pins = "GPIO31_V3"; - ste,config = <&gpio_in_pd>; - }; - /* GPIO 32 used for DRDY, pull this down */ - tvk_cfg2 { - pins = "GPIO32_V2"; - ste,config = <&gpio_in_pd>; - }; - }; - }; - synaptics { - synaptics_tvk_mode: synaptics_tvk { - /* Touchscreen uses GPIO 84 */ - tvk_cfg1 { - pins = "GPIO84_C2"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - }; - }; -}; |