1 files changed, 0 insertions, 134 deletions
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
deleted file mode 100644
index 9d62f910cddf..000000000000
--- a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
+++ /dev/null
@@ -1,134 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Marvell RD88F6181 Common Board descrition
- *
- * Andrew Lunn <andrew@lunn.ch>
- *
- * This file contains the definitions that are common between the two
- * variants of the Marvell Kirkwood Development Board.
- */
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6281.dtsi"
-
-/ {
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8";
-		stdout-path = &uart0;
-	};
-
-	ocp@f1000000 {
-		pinctrl: pin-controller@10000 {
-			pinctrl-names = "default";
-
-			pmx_sdio_cd: pmx-sdio-cd {
-				marvell,pins = "mpp28";
-				marvell,function = "gpio";
-			};
-		};
-
-		serial@12000 {
-			status = "okay";
-
-		};
-
-		sata@80000 {
-			status = "okay";
-			nr-ports = <2>;
-		};
-		mvsdio@90000 {
-			pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>;
-			pinctrl-names = "default";
-			status = "okay";
-			cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-			/* No WP GPIO */
-		};
-	};
-};
-
-&nand {
-	status = "okay";
-
-	partition@0 {
-		label = "u-boot";
-		reg = <0x0000000 0x100000>;
-		read-only;
-	};
-
-	partition@100000 {
-		label = "uImage";
-		reg = <0x0100000 0x200000>;
-	};
-
-	partition@300000 {
-		label = "rootfs";
-		reg = <0x0300000 0x500000>;
-	};
-};
-
-&mdio {
-	status = "okay";
-
-	switch: switch@0 {
-		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				label = "lan1";
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "lan2";
-			};
-
-			port@2 {
-				reg = <2>;
-				label = "lan3";
-			};
-
-			port@3 {
-				reg = <3>;
-				label = "lan4";
-			};
-
-			port@5 {
-				reg = <5>;
-				phy-mode = "rgmii-id";
-				ethernet = <&eth0port>;
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-
-		};
-	};
-};
-
-&eth0 {
-	status = "okay";
-	ethernet0-port@0 {
-		speed = <1000>;
-		duplex = <1>;
-	};
-};
-
-&pciec {
-	status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-};