diff options
Diffstat (limited to 'arch/arm/boot/dts/dra72-evm.dts')
| -rw-r--r-- | arch/arm/boot/dts/dra72-evm.dts | 321 |
1 files changed, 320 insertions, 1 deletions
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index 41074288adfa..89085d066c65 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -17,6 +17,13 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1024 MB */ }; + + evm_3v3: fixedregulator-evm_3v3 { + compatible = "regulator-fixed"; + regulator-name = "evm_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; }; &dra7_pmx_core { @@ -26,6 +33,94 @@ 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ >; }; + + nand_default: nand_default { + pinctrl-single,pins = < + 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ + 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ + 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ + 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ + 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ + 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ + 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ + 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ + 0x20 (PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ + 0x24 (PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ + 0x28 (PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ + 0x2c (PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ + 0x30 (PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ + 0x34 (PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ + 0x38 (PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ + 0x3c (PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ + 0xd8 (PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ + >; + }; + + usb1_pins: pinmux_usb1_pins { + pinctrl-single,pins = < + 0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ + >; + }; + + usb2_pins: pinmux_usb2_pins { + pinctrl-single,pins = < + 0x284 (PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ + >; + }; + + tps65917_pins_default: tps65917_pins_default { + pinctrl-single,pins = < + 0x424 (PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ + >; + }; + + mmc1_pins_default: mmc1_pins_default { + pinctrl-single,pins = < + 0x36c (PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ + 0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */ + 0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */ + 0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */ + 0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */ + 0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */ + 0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */ + >; + }; + + mmc2_pins_default: mmc2_pins_default { + pinctrl-single,pins = < + 0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */ + 0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */ + 0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */ + 0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */ + 0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */ + 0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */ + 0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */ + 0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */ + 0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */ + 0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */ + >; + }; + + dcan1_pins_default: dcan1_pins_default { + pinctrl-single,pins = < + 0x3d0 (PIN_OUTPUT | MUX_MODE0) /* dcan1_tx */ + 0x3d4 (MUX_MODE15) /* dcan1_rx.off */ + 0x418 (PULL_DIS | MUX_MODE1) /* wakeup0.dcan1_rx */ + >; + }; + + dcan1_pins_sleep: dcan1_pins_sleep { + pinctrl-single,pins = < + 0x3d0 (MUX_MODE15) /* dcan1_tx.off */ + 0x3d4 (MUX_MODE15) /* dcan1_rx.off */ + 0x418 (MUX_MODE15) /* wakeup0.off */ + >; + }; }; &i2c1 { @@ -38,6 +133,9 @@ compatible = "ti,tps65917"; reg = <0x58>; + pinctrl-names = "default"; + pinctrl-0 = <&tps65917_pins_default>; + interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ interrupt-parent = <&gic>; interrupt-controller; @@ -62,7 +160,7 @@ /* VDD_CORE */ regulator-name = "smps2"; regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1030000>; + regulator-max-microvolt = <1060000>; regulator-boot-on; regulator-always-on; }; @@ -136,9 +234,230 @@ }; }; }; + + tps65917_power_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps65917>; + interrupts = <1 IRQ_TYPE_NONE>; + wakeup-source; + ti,palmas-long-press-seconds = <6>; + }; }; }; &uart1 { status = "okay"; }; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_default>; + ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */ + nand@0,0 { + /* To use NAND, DIP switch SW5 must be set like so: + * SW5.1 (NAND_SELn) = ON (LOW) + * SW5.9 (GPMC_WPN) = OFF (HIGH) + */ + reg = <0 0 4>; /* device IO registers */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <16>; + gpmc,device-width = <2>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <80>; + gpmc,cs-wr-off-ns = <80>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <60>; + gpmc,adv-wr-off-ns = <60>; + gpmc,we-on-ns = <10>; + gpmc,we-off-ns = <50>; + gpmc,oe-on-ns = <4>; + gpmc,oe-off-ns = <40>; + gpmc,access-ns = <40>; + gpmc,wr-access-ns = <80>; + gpmc,rd-cycle-ns = <80>; + gpmc,wr-cycle-ns = <80>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-data-mux-bus-ns = <0>; + /* MTD partition table */ + /* All SPL-* partitions are sized to minimal length + * which can be independently programmable. For + * NAND flash this is equal to size of erase-block */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "NAND.SPL"; + reg = <0x00000000 0x000020000>; + }; + partition@1 { + label = "NAND.SPL.backup1"; + reg = <0x00020000 0x00020000>; + }; + partition@2 { + label = "NAND.SPL.backup2"; + reg = <0x00040000 0x00020000>; + }; + partition@3 { + label = "NAND.SPL.backup3"; + reg = <0x00060000 0x00020000>; + }; + partition@4 { + label = "NAND.u-boot-spl-os"; + reg = <0x00080000 0x00040000>; + }; + partition@5 { + label = "NAND.u-boot"; + reg = <0x000c0000 0x00100000>; + }; + partition@6 { + label = "NAND.u-boot-env"; + reg = <0x001c0000 0x00020000>; + }; + partition@7 { + label = "NAND.u-boot-env.backup1"; + reg = <0x001e0000 0x00020000>; + }; + partition@8 { + label = "NAND.kernel"; + reg = <0x00200000 0x00800000>; + }; + partition@9 { + label = "NAND.file-system"; + reg = <0x00a00000 0x0f600000>; + }; + }; +}; + +&usb2_phy1 { + phy-supply = <&ldo4_reg>; +}; + +&usb2_phy2 { + phy-supply = <&ldo4_reg>; +}; + +&usb1 { + dr_mode = "peripheral"; + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins>; +}; + +&usb2 { + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb2_pins>; +}; + +&mmc1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_default>; + + vmmc-supply = <&ldo1_reg>; + bus-width = <4>; + /* + * SDCD signal is not being used here - using the fact that GPIO mode + * is a viable alternative + */ + cd-gpios = <&gpio6 27 0>; +}; + +&mmc2 { + /* SW5-3 in ON position */ + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_default>; + + vmmc-supply = <&evm_3v3>; + bus-width = <8>; + ti,non-removable; +}; + +&dra7_pmx_core { + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 2 */ + 0x198 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ + 0x19c (PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ + 0x1a0 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ + 0x1a4 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ + 0x1a8 (PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ + 0x1ac (PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ + 0x1b0 (PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ + 0x1b4 (PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ + 0x1b8 (PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ + 0x1bc (PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ + 0x1c0 (PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ + 0x1c4 (PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ + >; + + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 2 */ + 0x198 (MUX_MODE15) + 0x19c (MUX_MODE15) + 0x1a0 (MUX_MODE15) + 0x1a4 (MUX_MODE15) + 0x1a8 (MUX_MODE15) + 0x1ac (MUX_MODE15) + 0x1b0 (MUX_MODE15) + 0x1b4 (MUX_MODE15) + 0x1b8 (MUX_MODE15) + 0x1bc (MUX_MODE15) + 0x1c0 (MUX_MODE15) + 0x1c4 (MUX_MODE15) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + 0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ + 0x240 (PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + 0x23c (MUX_MODE15) + 0x240 (MUX_MODE15) + >; + }; +}; + +&mac { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <3>; + phy-mode = "rgmii"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + active_slave = <1>; +}; + +&dcan1 { + status = "ok"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dcan1_pins_default>; + pinctrl-1 = <&dcan1_pins_sleep>; +}; |