aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst')
-rw-r--r--Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst700
1 files changed, 700 insertions, 0 deletions
diff --git a/Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst b/Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst
new file mode 100644
index 000000000000..5d46e5036129
--- /dev/null
+++ b/Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst
@@ -0,0 +1,700 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+==============================================================
+Linux Driver for the Synopsys(R) Ethernet Controllers "stmmac"
+==============================================================
+
+Authors: Giuseppe Cavallaro <peppe.cavallaro@st.com>,
+Alexandre Torgue <alexandre.torgue@st.com>, Jose Abreu <joabreu@synopsys.com>
+
+Contents
+========
+
+- In This Release
+- Feature List
+- Kernel Configuration
+- Command Line Parameters
+- Driver Information and Notes
+- Debug Information
+- Support
+
+In This Release
+===============
+
+This file describes the stmmac Linux Driver for all the Synopsys(R) Ethernet
+Controllers.
+
+Currently, this network device driver is for all STi embedded MAC/GMAC
+(i.e. 7xxx/5xxx SoCs), SPEAr (arm), Loongson1B (mips) and XILINX XC2V3000
+FF1152AMT0221 D1215994A VIRTEX FPGA board. The Synopsys Ethernet QoS 5.0 IPK
+is also supported.
+
+DesignWare(R) Cores Ethernet MAC 10/100/1000 Universal version 3.70a
+(and older) and DesignWare(R) Cores Ethernet Quality-of-Service version 4.0
+(and upper) have been used for developing this driver as well as
+DesignWare(R) Cores XGMAC - 10G Ethernet MAC and DesignWare(R) Cores
+Enterprise MAC - 100G Ethernet MAC.
+
+This driver supports both the platform bus and PCI.
+
+This driver includes support for the following Synopsys(R) DesignWare(R)
+Cores Ethernet Controllers and corresponding minimum and maximum versions:
+
++-------------------------------+--------------+--------------+--------------+
+| Controller Name | Min. Version | Max. Version | Abbrev. Name |
++===============================+==============+==============+==============+
+| Ethernet MAC Universal | N/A | 3.73a | GMAC |
++-------------------------------+--------------+--------------+--------------+
+| Ethernet Quality-of-Service | 4.00a | N/A | GMAC4+ |
++-------------------------------+--------------+--------------+--------------+
+| XGMAC - 10G Ethernet MAC | 2.10a | N/A | XGMAC2+ |
++-------------------------------+--------------+--------------+--------------+
+| XLGMAC - 100G Ethernet MAC | 2.00a | N/A | XLGMAC2+ |
++-------------------------------+--------------+--------------+--------------+
+
+For questions related to hardware requirements, refer to the documentation
+supplied with your Ethernet adapter. All hardware requirements listed apply
+to use with Linux.
+
+Feature List
+============
+
+The following features are available in this driver:
+ - GMII/MII/RGMII/SGMII/RMII/XGMII/XLGMII Interface
+ - Half-Duplex / Full-Duplex Operation
+ - Energy Efficient Ethernet (EEE)
+ - IEEE 802.3x PAUSE Packets (Flow Control)
+ - RMON/MIB Counters
+ - IEEE 1588 Timestamping (PTP)
+ - Pulse-Per-Second Output (PPS)
+ - MDIO Clause 22 / Clause 45 Interface
+ - MAC Loopback
+ - ARP Offloading
+ - Automatic CRC / PAD Insertion and Checking
+ - Checksum Offload for Received and Transmitted Packets
+ - Standard or Jumbo Ethernet Packets
+ - Source Address Insertion / Replacement
+ - VLAN TAG Insertion / Replacement / Deletion / Filtering (HASH and PERFECT)
+ - Programmable TX and RX Watchdog and Coalesce Settings
+ - Destination Address Filtering (PERFECT)
+ - HASH Filtering (Multicast)
+ - Layer 3 / Layer 4 Filtering
+ - Remote Wake-Up Detection
+ - Receive Side Scaling (RSS)
+ - Frame Preemption for TX and RX
+ - Programmable Burst Length, Threshold, Queue Size
+ - Multiple Queues (up to 8)
+ - Multiple Scheduling Algorithms (TX: WRR, DWRR, WFQ, SP, CBS, EST, TBS;
+ RX: WRR, SP)
+ - Flexible RX Parser
+ - TCP / UDP Segmentation Offload (TSO, USO)
+ - Split Header (SPH)
+ - Safety Features (ECC Protection, Data Parity Protection)
+ - Selftests using Ethtool
+
+Kernel Configuration
+====================
+
+The kernel configuration option is ``CONFIG_STMMAC_ETH``:
+ - ``CONFIG_STMMAC_PLATFORM``: is to enable the platform driver.
+ - ``CONFIG_STMMAC_PCI``: is to enable the pci driver.
+
+Command Line Parameters
+=======================
+
+If the driver is built as a module the following optional parameters are used
+by entering them on the command line with the modprobe command using this
+syntax (e.g. for PCI module)::
+
+ modprobe stmmac_pci [<option>=<VAL1>,<VAL2>,...]
+
+Driver parameters can be also passed in command line by using::
+
+ stmmaceth=watchdog:100,chain_mode=1
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+watchdog
+--------
+:Valid Range: 5000-None
+:Default Value: 5000
+
+This parameter overrides the transmit timeout in milliseconds.
+
+debug
+-----
+:Valid Range: 0-16 (0=none,...,16=all)
+:Default Value: 0
+
+This parameter adjusts the level of debug messages displayed in the system
+logs.
+
+phyaddr
+-------
+:Valid Range: 0-31
+:Default Value: -1
+
+This parameter overrides the physical address of the PHY device.
+
+flow_ctrl
+---------
+:Valid Range: 0-3 (0=off,1=rx,2=tx,3=rx/tx)
+:Default Value: 3
+
+This parameter changes the default Flow Control ability.
+
+pause
+-----
+:Valid Range: 0-65535
+:Default Value: 65535
+
+This parameter changes the default Flow Control Pause time.
+
+tc
+--
+:Valid Range: 64-256
+:Default Value: 64
+
+This parameter changes the default HW FIFO Threshold control value.
+
+buf_sz
+------
+:Valid Range: 1536-16384
+:Default Value: 1536
+
+This parameter changes the default RX DMA packet buffer size.
+
+eee_timer
+---------
+:Valid Range: 0-None
+:Default Value: 1000
+
+This parameter changes the default LPI TX Expiration time in milliseconds.
+
+chain_mode
+----------
+:Valid Range: 0-1 (0=off,1=on)
+:Default Value: 0
+
+This parameter changes the default mode of operation from Ring Mode to
+Chain Mode.
+
+Driver Information and Notes
+============================
+
+Transmit Process
+----------------
+
+The xmit method is invoked when the kernel needs to transmit a packet; it sets
+the descriptors in the ring and informs the DMA engine that there is a packet
+ready to be transmitted.
+
+By default, the driver sets the ``NETIF_F_SG`` bit in the features field of
+the ``net_device`` structure, enabling the scatter-gather feature. This is
+true on chips and configurations where the checksum can be done in hardware.
+
+Once the controller has finished transmitting the packet, timer will be
+scheduled to release the transmit resources.
+
+Receive Process
+---------------
+
+When one or more packets are received, an interrupt happens. The interrupts
+are not queued, so the driver has to scan all the descriptors in the ring
+during the receive process.
+
+This is based on NAPI, so the interrupt handler signals only if there is work
+to be done, and it exits. Then the poll method will be scheduled at some
+future point.
+
+The incoming packets are stored, by the DMA, in a list of pre-allocated socket
+buffers in order to avoid the memcpy (zero-copy).
+
+Interrupt Mitigation
+--------------------
+
+The driver is able to mitigate the number of its DMA interrupts using NAPI for
+the reception on chips older than the 3.50. New chips have an HW RX Watchdog
+used for this mitigation.
+
+Mitigation parameters can be tuned by ethtool.
+
+WoL
+---
+
+Wake up on Lan feature through Magic and Unicast frames are supported for the
+GMAC, GMAC4/5 and XGMAC core.
+
+DMA Descriptors
+---------------
+
+Driver handles both normal and alternate descriptors. The latter has been only
+tested on DesignWare(R) Cores Ethernet MAC Universal version 3.41a and later.
+
+stmmac supports DMA descriptor to operate both in dual buffer (RING) and
+linked-list(CHAINED) mode. In RING each descriptor points to two data buffer
+pointers whereas in CHAINED mode they point to only one data buffer pointer.
+RING mode is the default.
+
+In CHAINED mode each descriptor will have pointer to next descriptor in the
+list, hence creating the explicit chaining in the descriptor itself, whereas
+such explicit chaining is not possible in RING mode.
+
+Extended Descriptors
+--------------------
+
+The extended descriptors give us information about the Ethernet payload when
+it is carrying PTP packets or TCP/UDP/ICMP over IP. These are not available on
+GMAC Synopsys(R) chips older than the 3.50. At probe time the driver will
+decide if these can be actually used. This support also is mandatory for PTPv2
+because the extra descriptors are used for saving the hardware timestamps and
+Extended Status.
+
+Ethtool Support
+---------------
+
+Ethtool is supported. For example, driver statistics (including RMON),
+internal errors can be taken using::
+
+ ethtool -S ethX
+
+Ethtool selftests are also supported. This allows to do some early sanity
+checks to the HW using MAC and PHY loopback mechanisms::
+
+ ethtool -t ethX
+
+Jumbo and Segmentation Offloading
+---------------------------------
+
+Jumbo frames are supported and tested for the GMAC. The GSO has been also
+added but it's performed in software. LRO is not supported.
+
+TSO Support
+-----------
+
+TSO (TCP Segmentation Offload) feature is supported by GMAC > 4.x and XGMAC
+chip family. When a packet is sent through TCP protocol, the TCP stack ensures
+that the SKB provided to the low level driver (stmmac in our case) matches
+with the maximum frame len (IP header + TCP header + payload <= 1500 bytes
+(for MTU set to 1500)). It means that if an application using TCP want to send
+a packet which will have a length (after adding headers) > 1514 the packet
+will be split in several TCP packets: The data payload is split and headers
+(TCP/IP ..) are added. It is done by software.
+
+When TSO is enabled, the TCP stack doesn't care about the maximum frame length
+and provide SKB packet to stmmac as it is. The GMAC IP will have to perform
+the segmentation by it self to match with maximum frame length.
+
+This feature can be enabled in device tree through ``snps,tso`` entry.
+
+Energy Efficient Ethernet
+-------------------------
+
+Energy Efficient Ethernet (EEE) enables IEEE 802.3 MAC sublayer along with a
+family of Physical layer to operate in the Low Power Idle (LPI) mode. The EEE
+mode supports the IEEE 802.3 MAC operation at 100Mbps, 1000Mbps and 1Gbps.
+
+The LPI mode allows power saving by switching off parts of the communication
+device functionality when there is no data to be transmitted & received.
+The system on both the side of the link can disable some functionalities and
+save power during the period of low-link utilization. The MAC controls whether
+the system should enter or exit the LPI mode and communicate this to PHY.
+
+As soon as the interface is opened, the driver verifies if the EEE can be
+supported. This is done by looking at both the DMA HW capability register and
+the PHY devices MCD registers.
+
+To enter in TX LPI mode the driver needs to have a software timer that enable
+and disable the LPI mode when there is nothing to be transmitted.
+
+Precision Time Protocol (PTP)
+-----------------------------
+
+The driver supports the IEEE 1588-2002, Precision Time Protocol (PTP), which
+enables precise synchronization of clocks in measurement and control systems
+implemented with technologies such as network communication.
+
+In addition to the basic timestamp features mentioned in IEEE 1588-2002
+Timestamps, new GMAC cores support the advanced timestamp features.
+IEEE 1588-2008 can be enabled when configuring the Kernel.
+
+SGMII/RGMII Support
+-------------------
+
+New GMAC devices provide own way to manage RGMII/SGMII. This information is
+available at run-time by looking at the HW capability register. This means
+that the stmmac can manage auto-negotiation and link status w/o using the
+PHYLIB stuff. In fact, the HW provides a subset of extended registers to
+restart the ANE, verify Full/Half duplex mode and Speed. Thanks to these
+registers, it is possible to look at the Auto-negotiated Link Parter Ability.
+
+Physical
+--------
+
+The driver is compatible with Physical Abstraction Layer to be connected with
+PHY and GPHY devices.
+
+Platform Information
+--------------------
+
+Several information can be passed through the platform and device-tree.
+
+::
+
+ struct plat_stmmacenet_data {
+
+1) Bus identifier::
+
+ int bus_id;
+
+2) PHY Physical Address. If set to -1 the driver will pick the first PHY it
+finds::
+
+ int phy_addr;
+
+3) PHY Device Interface::
+
+ int interface;
+
+4) Specific platform fields for the MDIO bus::
+
+ struct stmmac_mdio_bus_data *mdio_bus_data;
+
+5) Internal DMA parameters::
+
+ struct stmmac_dma_cfg *dma_cfg;
+
+6) Fixed CSR Clock Range selection::
+
+ int clk_csr;
+
+7) HW uses the GMAC core::
+
+ int has_gmac;
+
+8) If set the MAC will use Enhanced Descriptors::
+
+ int enh_desc;
+
+9) Core is able to perform TX Checksum and/or RX Checksum in HW::
+
+ int tx_coe;
+ int rx_coe;
+
+11) Some HWs are not able to perform the csum in HW for over-sized frames due
+to limited buffer sizes. Setting this flag the csum will be done in SW on
+JUMBO frames::
+
+ int bugged_jumbo;
+
+12) Core has the embedded power module::
+
+ int pmt;
+
+13) Force DMA to use the Store and Forward mode or Threshold mode::
+
+ int force_sf_dma_mode;
+ int force_thresh_dma_mode;
+
+15) Force to disable the RX Watchdog feature and switch to NAPI mode::
+
+ int riwt_off;
+
+16) Limit the maximum operating speed and MTU::
+
+ int max_speed;
+ int maxmtu;
+
+18) Number of Multicast/Unicast filters::
+
+ int multicast_filter_bins;
+ int unicast_filter_entries;
+
+20) Limit the maximum TX and RX FIFO size::
+
+ int tx_fifo_size;
+ int rx_fifo_size;
+
+21) Use the specified number of TX and RX Queues::
+
+ u32 rx_queues_to_use;
+ u32 tx_queues_to_use;
+
+22) Use the specified TX and RX scheduling algorithm::
+
+ u8 rx_sched_algorithm;
+ u8 tx_sched_algorithm;
+
+23) Internal TX and RX Queue parameters::
+
+ struct stmmac_rxq_cfg rx_queues_cfg[MTL_MAX_RX_QUEUES];
+ struct stmmac_txq_cfg tx_queues_cfg[MTL_MAX_TX_QUEUES];
+
+24) This callback is used for modifying some syscfg registers (on ST SoCs)
+according to the link speed negotiated by the physical layer::
+
+ void (*fix_mac_speed)(void *priv, unsigned int speed);
+
+25) Callbacks used for calling a custom initialization; This is sometimes
+necessary on some platforms (e.g. ST boxes) where the HW needs to have set
+some PIO lines or system cfg registers. init/exit callbacks should not use
+or modify platform data::
+
+ int (*init)(struct platform_device *pdev, void *priv);
+ void (*exit)(struct platform_device *pdev, void *priv);
+
+26) Perform HW setup of the bus. For example, on some ST platforms this field
+is used to configure the AMBA bridge to generate more efficient STBus traffic::
+
+ struct mac_device_info *(*setup)(void *priv);
+ void *bsp_priv;
+
+27) Internal clocks and rates::
+
+ struct clk *stmmac_clk;
+ struct clk *pclk;
+ struct clk *clk_ptp_ref;
+ unsigned int clk_ptp_rate;
+ unsigned int clk_ref_rate;
+ s32 ptp_max_adj;
+
+28) Main reset::
+
+ struct reset_control *stmmac_rst;
+
+29) AXI Internal Parameters::
+
+ struct stmmac_axi *axi;
+
+30) HW uses GMAC>4 cores::
+
+ int has_gmac4;
+
+31) HW is sun8i based::
+
+ bool has_sun8i;
+
+32) Enables TSO feature::
+
+ bool tso_en;
+
+33) Enables Receive Side Scaling (RSS) feature::
+
+ int rss_en;
+
+34) MAC Port selection::
+
+ int mac_port_sel_speed;
+
+35) Enables TX LPI Clock Gating::
+
+ bool en_tx_lpi_clockgating;
+
+36) HW uses XGMAC>2.10 cores::
+
+ int has_xgmac;
+
+::
+
+ }
+
+For MDIO bus data, we have:
+
+::
+
+ struct stmmac_mdio_bus_data {
+
+1) PHY mask passed when MDIO bus is registered::
+
+ unsigned int phy_mask;
+
+2) List of IRQs, one per PHY::
+
+ int *irqs;
+
+3) If IRQs is NULL, use this for probed PHY::
+
+ int probed_phy_irq;
+
+4) Set to true if PHY needs reset::
+
+ bool needs_reset;
+
+::
+
+ }
+
+For DMA engine configuration, we have:
+
+::
+
+ struct stmmac_dma_cfg {
+
+1) Programmable Burst Length (TX and RX)::
+
+ int pbl;
+
+2) If set, DMA TX / RX will use this value rather than pbl::
+
+ int txpbl;
+ int rxpbl;
+
+3) Enable 8xPBL::
+
+ bool pblx8;
+
+4) Enable Fixed or Mixed burst::
+
+ int fixed_burst;
+ int mixed_burst;
+
+5) Enable Address Aligned Beats::
+
+ bool aal;
+
+6) Enable Enhanced Addressing (> 32 bits)::
+
+ bool eame;
+
+::
+
+ }
+
+For DMA AXI parameters, we have:
+
+::
+
+ struct stmmac_axi {
+
+1) Enable AXI LPI::
+
+ bool axi_lpi_en;
+ bool axi_xit_frm;
+
+2) Set AXI Write / Read maximum outstanding requests::
+
+ u32 axi_wr_osr_lmt;
+ u32 axi_rd_osr_lmt;
+
+3) Set AXI 4KB bursts::
+
+ bool axi_kbbe;
+
+4) Set AXI maximum burst length map::
+
+ u32 axi_blen[AXI_BLEN];
+
+5) Set AXI Fixed burst / mixed burst::
+
+ bool axi_fb;
+ bool axi_mb;
+
+6) Set AXI rebuild incrx mode::
+
+ bool axi_rb;
+
+::
+
+ }
+
+For the RX Queues configuration, we have:
+
+::
+
+ struct stmmac_rxq_cfg {
+
+1) Mode to use (DCB or AVB)::
+
+ u8 mode_to_use;
+
+2) DMA channel to use::
+
+ u32 chan;
+
+3) Packet routing, if applicable::
+
+ u8 pkt_route;
+
+4) Use priority routing, and priority to route::
+
+ bool use_prio;
+ u32 prio;
+
+::
+
+ }
+
+For the TX Queues configuration, we have:
+
+::
+
+ struct stmmac_txq_cfg {
+
+1) Queue weight in scheduler::
+
+ u32 weight;
+
+2) Mode to use (DCB or AVB)::
+
+ u8 mode_to_use;
+
+3) Credit Base Shaper Parameters::
+
+ u32 send_slope;
+ u32 idle_slope;
+ u32 high_credit;
+ u32 low_credit;
+
+4) Use priority scheduling, and priority::
+
+ bool use_prio;
+ u32 prio;
+
+::
+
+ }
+
+Device Tree Information
+-----------------------
+
+Please refer to the following document:
+Documentation/devicetree/bindings/net/snps,dwmac.yaml
+
+HW Capabilities
+---------------
+
+Note that, starting from new chips, where it is available the HW capability
+register, many configurations are discovered at run-time for example to
+understand if EEE, HW csum, PTP, enhanced descriptor etc are actually
+available. As strategy adopted in this driver, the information from the HW
+capability register can replace what has been passed from the platform.
+
+Debug Information
+=================
+
+The driver exports many information i.e. internal statistics, debug
+information, MAC and DMA registers etc.
+
+These can be read in several ways depending on the type of the information
+actually needed.
+
+For example a user can be use the ethtool support to get statistics: e.g.
+using: ``ethtool -S ethX`` (that shows the Management counters (MMC) if
+supported) or sees the MAC/DMA registers: e.g. using: ``ethtool -d ethX``
+
+Compiling the Kernel with ``CONFIG_DEBUG_FS`` the driver will export the
+following debugfs entries:
+
+ - ``descriptors_status``: To show the DMA TX/RX descriptor rings
+ - ``dma_cap``: To show the HW Capabilities
+
+Developer can also use the ``debug`` module parameter to get further debug
+information (please see: NETIF Msg Level).
+
+Support
+=======
+
+If an issue is identified with the released source code on a supported kernel
+with a supported adapter, email the specific information related to the
+issue to netdev@vger.kernel.org