1 files changed, 0 insertions, 83 deletions
diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt
deleted file mode 100644
index 68cccc4653ba..000000000000
--- a/Documentation/devicetree/bindings/sound/wm8994.txt
+++ /dev/null
@@ -1,83 +0,0 @@
-WM1811/WM8994/WM8958 audio CODEC
-
-These devices support both I2C and SPI (configured with pin strapping
-on the board).
-
-Required properties:
-
-  - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958".
-
-  - reg : the I2C address of the device for I2C, the chip select
-          number for SPI.
-
-  - gpio-controller : Indicates this device is a GPIO controller.
-  - #gpio-cells : Must be 2. The first cell is the pin number and the
-    second cell is used to specify optional parameters (currently unused).
-
-  - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply,
-    SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered
-    in Documentation/devicetree/bindings/regulator/regulator.txt
-
-Optional properties:
-
-  - interrupts : The interrupt line the IRQ signal for the device is
-    connected to.  This is optional, if it is not connected then none
-    of the interrupt related properties should be specified.
-  - interrupt-controller : These devices contain interrupt controllers
-    and may provide interrupt services to other devices if they have an
-    interrupt line connected.
-  - #interrupt-cells: the number of cells to describe an IRQ, this should be 2.
-    The first cell is the IRQ number.
-    The second cell is the flags, encoded as the trigger masks from
-    Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-
-  - clocks : A list of up to two phandle and clock specifier pairs
-  - clock-names : A list of clock names sorted in the same order as clocks.
-                  Valid clock names are "MCLK1" and "MCLK2".
-
-  - wlf,gpio-cfg : A list of GPIO configuration register values. If absent,
-    no configuration of these registers is performed. If any value is
-    over 0xffff then the register will be left as default. If present 11
-    values must be supplied.
-
-  - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or
-    WM8958.  If absent the register defaults will be used.
-
-  - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device.
-  - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device.
-
-  - wlf,lineout1-se : If present LINEOUT1 is in single ended mode.
-  - wlf,lineout2-se : If present LINEOUT2 is in single ended mode.
-
-  - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback
-    connected.
-  - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback
-    connected.
-
-  - wlf,ldoena-always-driven : If present LDOENA is always driven.
-
-  - wlf,spkmode-pu : If present enable the internal pull-up resistor on
-    the SPKMODE pin.
-
-  - wlf,csnaddr-pd : If present enable the internal pull-down resistor on
-    the CS/ADDR pin.
-
-Example:
-
-wm8994: codec@1a {
-	compatible = "wlf,wm8994";
-	reg = <0x1a>;
-
-	gpio-controller;
-	#gpio-cells = <2>;
-
-	lineout1-se;
-
-	AVDD2-supply = <&regulator>;
-	CPVDD-supply = <&regulator>;
-	DBVDD1-supply = <&regulator>;
-	DBVDD2-supply = <&regulator>;
-	DBVDD3-supply = <&regulator>;
-	SPKVDD1-supply = <&regulator>;
-	SPKVDD2-supply = <&regulator>;
-};