diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml | 159 |
1 files changed, 65 insertions, 94 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml index 63d1cfe86c6e..7c3e5e043f07 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml @@ -7,11 +7,10 @@ $schema: http://devicetree.org/meta-schemas/core.yaml# title: Qualcomm Technologies, Inc. IPQ6018 TLMM block maintainers: - - Sricharan R <sricharan@codeaurora.org> + - Bjorn Andersson <andersson@kernel.org> -description: | - This binding describes the Top Level Mode Multiplexer block found in the - IPQ6018 platform. +description: + Top Level Mode Multiplexer pin controller in Qualcomm IPQ6018 SoC. properties: compatible: @@ -21,36 +20,30 @@ properties: maxItems: 1 interrupts: - description: Specifies the TLMM summary IRQ maxItems: 1 interrupt-controller: true - - '#interrupt-cells': - description: - Specifies the PIN numbers and Flags, as defined in defined in - include/dt-bindings/interrupt-controller/irq.h - const: 2 - + "#interrupt-cells": true gpio-controller: true + "#gpio-cells": true + gpio-ranges: true - '#gpio-cells': - description: Specifying the pin number and flags, as defined in - include/dt-bindings/gpio/gpio.h - const: 2 - - gpio-ranges: - maxItems: 1 - -#PIN CONFIGURATION NODES patternProperties: - '-pinmux$': - type: object + "-state$": + oneOf: + - $ref: "#/$defs/qcom-ipq6018-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-ipq6018-tlmm-state" + additionalProperties: false + +$defs: + qcom-ipq6018-tlmm-state: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - allOf: - - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -61,93 +54,71 @@ patternProperties: oneOf: - pattern: "^gpio([1-9]|[1-7][0-9]|80)$" - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, - sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, - qdsd_data3 ] + sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, + qdsd_data3 ] minItems: 1 - maxItems: 4 + maxItems: 16 function: description: Specify the alternative function to be configured for the specified pins. enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, - atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac, - atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0, - atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c, - blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi, - blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi, - blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi, - blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi, - blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst, - cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0, - cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v, - dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass, - flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, - gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, - gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, - ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, - nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, - pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, - pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, - pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, - qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, - qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, - qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, - qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write, - sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, - uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] - - drive-strength: - enum: [2, 4, 6, 8, 10, 12, 14, 16] - default: 2 - description: - Selects the drive strength for the specified pins, in mA. - - bias-pull-down: true - - bias-pull-up: true - - bias-disable: true - - output-high: true - - output-low: true + atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac, + atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0, + atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp0_i2c, blsp1_i2c, + blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp0_spi, blsp1_spi, + blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi, + blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi, + blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi, + blsp0_uart, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst, + cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v, + dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass, + flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, + gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, + gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, + ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, + nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, + pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b, + pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, + pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, + qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, + qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, + qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, + qdss_tracedata_a, qdss_tracedata_b, qpic_pad, reset_n, sd_card, + sd_write, sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, + uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] required: - pins - - function - additionalProperties: false +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# required: - compatible - reg - - interrupts - - interrupt-controller - - '#interrupt-cells' - - gpio-controller - - '#gpio-cells' - - gpio-ranges additionalProperties: false examples: - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - tlmm: pinctrl@1000000 { - compatible = "qcom,ipq6018-pinctrl"; - reg = <0x01000000 0x300000>; - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - interrupt-controller; - #interrupt-cells = <2>; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&tlmm 0 80>; - - serial3-pinmux { - pins = "gpio44", "gpio45"; - function = "blsp2_uart"; - drive-strength = <8>; - bias-pull-down; - }; + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq6018-pinctrl"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 80>; + + serial3-state { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; }; + }; |