aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt')
-rw-r--r--Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt92
1 files changed, 0 insertions, 92 deletions
diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
deleted file mode 100644
index c02259353327..000000000000
--- a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
+++ /dev/null
@@ -1,92 +0,0 @@
-* Ingenic JZ4780 NAND/ECC
-
-This file documents the device tree bindings for NAND flash devices on the
-JZ4780. NAND devices are connected to the NEMC controller (described in
-memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
-be children of the NEMC node.
-
-Required NAND controller device properties:
-- compatible: Should be one of:
- * ingenic,jz4740-nand
- * ingenic,jz4725b-nand
- * ingenic,jz4780-nand
-- reg: For each bank with a NAND chip attached, should specify a bank number,
- an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
-
-Optional NAND controller device properties:
-- ecc-engine: To make use of the hardware ECC controller, this
- property must contain a phandle for the ECC controller node. The required
- properties for this node are described below. If this is not specified,
- software ECC will be used instead.
-
-Optional children nodes:
-- Individual NAND chips are children of the NAND controller node.
-
-Required children node properties:
-- reg: An integer ranging from 1 to 6 representing the CS line to use.
-
-Optional children node properties:
-- nand-ecc-step-size: ECC block size in bytes.
-- nand-ecc-strength: ECC strength (max number of correctable bits).
-- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
-- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false
-- rb-gpios: GPIO specifier for the busy pin.
-- wp-gpios: GPIO specifier for the write protect pin.
-
-Optional child node of NAND chip nodes:
-- partitions: see Documentation/devicetree/bindings/mtd/partition.txt
-
-Example:
-
-nemc: nemc@13410000 {
- ...
-
- nandc: nand-controller@1 {
- compatible = "ingenic,jz4780-nand";
- reg = <1 0 0x1000000>; /* Bank 1 */
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- ecc-engine = <&bch>;
-
- nand@1 {
- reg = <1>;
-
- nand-ecc-step-size = <1024>;
- nand-ecc-strength = <24>;
- nand-ecc-mode = "hw";
- nand-on-flash-bbt;
-
- rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>;
-
- partitions {
- #address-cells = <2>;
- #size-cells = <2>;
- ...
- }
- };
- };
-};
-
-The ECC controller is a separate SoC component used for error correction on
-NAND devices. The following is a description of the device properties for a
-ECC controller.
-
-Required ECC properties:
-- compatible: Should be one of:
- * ingenic,jz4740-ecc
- * ingenic,jz4725b-bch
- * ingenic,jz4780-bch
-- reg: Should specify the ECC controller registers location and length.
-- clocks: Clock for the ECC controller.
-
-Example:
-
-bch: bch@134d0000 {
- compatible = "ingenic,jz4780-bch";
- reg = <0x134d0000 0x10000>;
-
- clocks = <&cgu JZ4780_CLK_BCH>;
-};