diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd/gpmi-nand.txt')
-rw-r--r-- | Documentation/devicetree/bindings/mtd/gpmi-nand.txt | 75 |
1 files changed, 0 insertions, 75 deletions
diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt deleted file mode 100644 index 393588385c6e..000000000000 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ /dev/null @@ -1,75 +0,0 @@ -* Freescale General-Purpose Media Interface (GPMI) - -The GPMI nand controller provides an interface to control the -NAND flash chips. - -Required properties: - - compatible : should be "fsl,<chip>-gpmi-nand", chip can be: - * imx23 - * imx28 - * imx6q - * imx6sx - * imx7d - - reg : should contain registers location and length for gpmi and bch. - - reg-names: Should contain the reg names "gpmi-nand" and "bch" - - interrupts : BCH interrupt number. - - interrupt-names : Should be "bch". - - dmas: DMA specifier, consisting of a phandle to DMA controller node - and GPMI DMA channel ID. - Refer to dma.txt and fsl-mxs-dma.txt for details. - - dma-names: Must be "rx-tx". - - clocks : clocks phandle and clock specifier corresponding to each clock - specified in clock-names. - - clock-names : The "gpmi_io" clock is always required. Which clocks are - exactly required depends on chip: - * imx23/imx28 : "gpmi_io" - * imx6q/sx : "gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch" - * imx7d : "gpmi_io", "gpmi_bch_apb" - -Optional properties: - - nand-on-flash-bbt: boolean to enable on flash bbt option if not - present false - - fsl,use-minimum-ecc: Protect this NAND flash with the minimum ECC - strength required. The required ECC strength is - automatically discoverable for some flash - (e.g., according to the ONFI standard). - However, note that if this strength is not - discoverable or this property is not enabled, - the software may chooses an implementation-defined - ECC scheme. - - fsl,no-blockmark-swap: Don't swap the bad block marker from the OOB - area with the byte in the data area but rely on the - flash based BBT for identifying bad blocks. - NOTE: this is only valid in conjunction with - 'nand-on-flash-bbt'. - WARNING: on i.MX28 blockmark swapping cannot be - disabled for the BootROM in the FCB. Thus, - partitions written from Linux with this feature - turned on may not be accessible by the BootROM - code. - - nand-ecc-strength: integer representing the number of bits to correct - per ECC step. Needs to be a multiple of 2. - - nand-ecc-step-size: integer representing the number of data bytes - that are covered by a single ECC step. The driver - supports 512 and 1024. - -The device tree may optionally contain sub-nodes describing partitions of the -address space. See partition.txt for more detail. - -Examples: - -gpmi-nand@8000c000 { - compatible = "fsl,imx28-gpmi-nand"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x8000c000 2000>, <0x8000a000 2000>; - reg-names = "gpmi-nand", "bch"; - interrupts = <41>; - interrupt-names = "bch"; - dmas = <&dma_apbh 4>; - dma-names = "rx-tx"; - - partition@0 { - ... - }; -}; |