diff options
Diffstat (limited to 'Documentation/devicetree/bindings/connector/usb-connector.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/connector/usb-connector.yaml | 343 |
1 files changed, 275 insertions, 68 deletions
diff --git a/Documentation/devicetree/bindings/connector/usb-connector.yaml b/Documentation/devicetree/bindings/connector/usb-connector.yaml index 4638d7adb806..1c4d3eb87763 100644 --- a/Documentation/devicetree/bindings/connector/usb-connector.yaml +++ b/Documentation/devicetree/bindings/connector/usb-connector.yaml @@ -11,14 +11,24 @@ maintainers: description: A USB connector node represents a physical USB connector. It should be a child - of a USB interface controller. + of a USB interface controller or a separate node when it is attached to both + MUX and USB interface controller. properties: compatible: - enum: - - usb-a-connector - - usb-b-connector - - usb-c-connector + oneOf: + - enum: + - usb-a-connector + - usb-b-connector + - usb-c-connector + + - items: + - const: gpio-usb-b-connector + - const: usb-b-connector + + - items: + - const: samsung,usb-connector-11pin + - const: usb-b-connector label: description: Symbolic name for the connector. @@ -27,8 +37,8 @@ properties: description: Size of the connector, should be specified in case of non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible connectors. - allOf: - - $ref: /schemas/types.yaml#definitions/string + $ref: /schemas/types.yaml#/definitions/string + enum: - mini - micro @@ -57,8 +67,8 @@ properties: power-role: description: Determines the power role that the Type C connector will support. "dual" refers to Dual Role Port (DRP). - allOf: - - $ref: /schemas/types.yaml#definitions/string + $ref: /schemas/types.yaml#/definitions/string + enum: - source - sink @@ -66,23 +76,44 @@ properties: try-power-role: description: Preferred power role. - allOf: - - $ref: /schemas/types.yaml#definitions/string + $ref: /schemas/types.yaml#/definitions/string + enum: - - source - - sink - - dual + - source + - sink + - dual data-role: description: Data role if Type C connector supports USB data. "dual" refers Dual Role Device (DRD). - allOf: - - $ref: /schemas/types.yaml#definitions/string + $ref: /schemas/types.yaml#/definitions/string + enum: - host - device - dual + typec-power-opmode: + description: Determines the power operation mode that the Type C connector + will support and will advertise through CC pins when it has no power + delivery support. + - "default" corresponds to default USB voltage and current defined by the + USB 2.0 and USB 3.2 specifications, 5V 500mA for USB 2.0 ports and + 5V 900mA or 1500mA for USB 3.2 ports in single-lane or dual-lane + operation respectively. + - "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB + Type-C Cable and Connector specification, when Power Delivery is not + supported. + $ref: /schemas/types.yaml#/definitions/string + enum: + - default + - 1.5A + - 3.0A + + pd-disable: + description: Set this property if the Type-C connector has no power delivery support. + type: boolean + # The following are optional properties for "usb-c-connector" with power # delivery support. source-pdos: @@ -95,8 +126,7 @@ properties: defined in dt-bindings/usb/pd.h. minItems: 1 maxItems: 7 - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array + $ref: /schemas/types.yaml#/definitions/uint32-array sink-pdos: description: An array of u32 with each entry providing supported power sink @@ -108,99 +138,276 @@ properties: in dt-bindings/usb/pd.h. minItems: 1 maxItems: 7 - allOf: - - $ref: /schemas/types.yaml#/definitions/uint32-array + $ref: /schemas/types.yaml#/definitions/uint32-array + + sink-vdos: + description: An array of u32 with each entry, a Vendor Defined Message Object (VDO), + providing additional information corresponding to the product, the detailed bit + definitions and the order of each VDO can be found in + "USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10" + chapter 6.4.4.3.1 Discover Identity. User can specify the VDO array via + VDO_IDH/_CERT/_PRODUCT/_UFP/_DFP/_PCABLE/_ACABLE(1/2)/_VPD() defined in + dt-bindings/usb/pd.h. + minItems: 3 + maxItems: 6 + $ref: /schemas/types.yaml#/definitions/uint32-array + + sink-vdos-v1: + description: An array of u32 with each entry, a Vendor Defined Message Object (VDO), + providing additional information corresponding to the product, the detailed bit + definitions and the order of each VDO can be found in + "USB Power Delivery Specification Revision 2.0, Version 1.3" chapter 6.4.4.3.1 Discover + Identity. User can specify the VDO array via VDO_IDH/_CERT/_PRODUCT/_CABLE/_AMA defined in + dt-bindings/usb/pd.h. + minItems: 3 + maxItems: 6 + $ref: /schemas/types.yaml#/definitions/uint32-array op-sink-microwatt: description: Sink required operating power in microwatt, if source can't offer the power, Capability Mismatch is set. Required for power sink and power dual role. + port: + $ref: /schemas/graph.yaml#/properties/port + description: OF graph bindings modeling a data bus to the connector, e.g. + there is a single High Speed (HS) port present in this connector. If there + is more than one bus (several port, with 'reg' property), they can be grouped + under 'ports'. + ports: - description: OF graph bindings (specified in bindings/graph.txt) that model - any data bus to the connector unless the bus is between parent node and - the connector. Since a single connector can have multiple data buses every - bus has an assigned OF graph port number as described below. - type: object + $ref: /schemas/graph.yaml#/properties/ports + description: OF graph bindings modeling any data bus to the connector + unless the bus is between parent node and the connector. Since a single + connector can have multiple data buses every bus has an assigned OF graph + port number as described below. + properties: port@0: - type: object + $ref: /schemas/graph.yaml#/properties/port description: High Speed (HS), present in all connectors. port@1: - type: object + $ref: /schemas/graph.yaml#/properties/port description: Super Speed (SS), present in SS capable connectors. port@2: - type: object + $ref: /schemas/graph.yaml#/properties/port description: Sideband Use (SBU), present in USB-C. This describes the alternate mode connection of which SBU is a part. required: - port@0 + new-source-frs-typec-current: + description: Initial current capability of the new source when vSafe5V + is applied during PD3.0 Fast Role Swap. "Table 6-14 Fixed Supply PDO - Sink" + of "USB Power Delivery Specification Revision 3.0, Version 1.2" provides the + different power levels and "6.4.1.3.1.6 Fast Role Swap USB Type-C Current" + provides a detailed description of the field. The sink PDO from current source + reflects the current source's(i.e. transmitter of the FRS signal) power + requirement during fr swap. The current sink (i.e. receiver of the FRS signal), + a.k.a new source, should check if it will be able to satisfy the current source's, + new sink's, requirement during frswap before enabling the frs signal reception. + This property refers to maximum current capability that the current sink can + satisfy. During FRS, VBUS voltage is at 5V, as the partners are in implicit + contract, hence, the power level is only a function of the current capability. + "1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink". + "2" refers to 1.5A@5V. + "3" refers to 3.0A@5V. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 3] + + slow-charger-loop: + description: Allows PMIC charger loops which are slow(i.e. cannot meet the 15ms deadline) to + still comply to pSnkStby i.e Maximum power that can be consumed by sink while in Sink Standby + state as defined in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification + Revision 3.0, Version 1.2. When the property is set, the port requests pSnkStby(2.5W - + 5V@500mA) upon entering SNK_DISCOVERY(instead of 3A or the 1.5A, Rp current advertised, during + SNK_DISCOVERY) and the actual currrent limit after reception of PS_Ready for PD link or during + SNK_READY for non-pd link. + type: boolean + +dependencies: + sink-vdos-v1: [ 'sink-vdos' ] + sink-vdos: [ 'sink-vdos-v1' ] + required: - compatible +allOf: + - if: + properties: + compatible: + contains: + const: gpio-usb-b-connector + then: + anyOf: + - required: + - vbus-gpios + - required: + - id-gpios + + - if: + properties: + compatible: + contains: + const: samsung,usb-connector-11pin + then: + properties: + type: + const: micro + +anyOf: + - not: + required: + - typec-power-opmode + - new-source-frs-typec-current + +additionalProperties: true + examples: # Micro-USB connector with HS lines routed via controller (MUIC). - - |+ + - | muic-max77843 { - usb_con1: connector { - compatible = "usb-b-connector"; - label = "micro-USB"; - type = "micro"; - }; + usb_con1: connector { + compatible = "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + }; }; # USB-C connector attached to CC controller (s2mm005), HS lines routed # to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort. # DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. - - |+ + - | ccic: s2mm005 { - usb_con2: connector { - compatible = "usb-c-connector"; - label = "USB-C"; + usb_con2: connector { + compatible = "usb-c-connector"; + label = "USB-C"; - ports { - #address-cells = <1>; - #size-cells = <0>; + ports { + #address-cells = <1>; + #size-cells = <0>; - port@0 { - reg = <0>; - usb_con_hs: endpoint { - remote-endpoint = <&max77865_usbc_hs>; - }; - }; - port@1 { - reg = <1>; - usb_con_ss: endpoint { - remote-endpoint = <&usbdrd_phy_ss>; + port@0 { + reg = <0>; + usb_con_hs: endpoint { + remote-endpoint = <&max77865_usbc_hs>; + }; + }; + port@1 { + reg = <1>; + usb_con_ss: endpoint { + remote-endpoint = <&usbdrd_phy_ss>; + }; + }; + port@2 { + reg = <2>; + usb_con_sbu: endpoint { + remote-endpoint = <&dp_aux>; + }; + }; }; - }; - port@2 { - reg = <2>; - usb_con_sbu: endpoint { - remote-endpoint = <&dp_aux>; - }; - }; }; - }; }; # USB-C connector attached to a typec port controller(ptn5110), which has # power delivery support and enables drp. - - |+ + - | #include <dt-bindings/usb/pd.h> typec: ptn5110 { - usb_con3: connector { + usb_con3: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 12000, 2000)>; + op-sink-microwatt = <10000000>; + }; + }; + + # USB-C connector attached to SoC with a single High-Speed controller + - | + connector { compatible = "usb-c-connector"; label = "USB-C"; - power-role = "dual"; - try-power-role = "sink"; - source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; - sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) - PDO_VAR(5000, 12000, 2000)>; - op-sink-microwatt = <10000000>; - }; + + port { + high_speed_ep: endpoint { + remote-endpoint = <&usb_hs_ep>; + }; + }; + }; + + # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220) + # with SS 2:1 MUX. HS lines routed to SoC, SS lines routed to the MUX and + # the output of MUX is connected to the SoC. + - | + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + hs_ep: endpoint { + remote-endpoint = <&usb3_hs_ep>; + }; + }; + port@1 { + reg = <1>; + ss_ep: endpoint { + remote-endpoint = <&hd3ss3220_in_ep>; + }; + }; + }; + }; + + # USB connector with GPIO control lines + - | + #include <dt-bindings/gpio/gpio.h> + + usb { + connector { + compatible = "gpio-usb-b-connector", "usb-b-connector"; + type = "micro"; + id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; + vbus-supply = <&usb_p0_vbus>; + }; + }; + + # Micro-USB connector with HS lines routed via controller (MUIC) and MHL + # lines connected to HDMI-MHL bridge (sii8620) on Samsung Exynos5433-based + # mobile phone + - | + muic-max77843 { + usb_con4: connector { + compatible = "samsung,usb-connector-11pin", "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + muic_to_usb: endpoint { + remote-endpoint = <&usb_to_muic>; + }; + }; + port@3 { + reg = <3>; + usb_con_mhl: endpoint { + remote-endpoint = <&sii8620_mhl>; + }; + }; + }; + }; }; |